User manual HILTI DX860-ENP

[. . . ] DX 860-ENP Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Gebruiksaanwijzing Manual de instrucciones Brugsanvisning Käyttöohje Bruksanvisning Instrukcja obslugi Návod na obsluhu Návod k obsluze Kasutusjuhend de en fr it nl es da fi sv pl sk cs et ja 282483 *282483* 1 2 1 2 3 1 2 4x 4 5 A max. min. h C 2 1 D h E h F h h 6 7 2 1 8 1 3 9 2 2 2/4 3 4 1 10 X-ENP Base material thickness (mm) Standard steel High-strength steel 20 4 red 4 black 15 3 10 blue 3 4 3 6 S 235, S275 E 36, ST 37, 340-470 N/mm2 S 355, S275 E 42, ST 52, 490-630 N/mm2 11 3 8 9 2 4 10 1 7 5 11 red 8 4 3 12 3 2 4 6 1 5 13 7 8 10 9 11 11 14 14 15 12 13 16 17 DX 860-ENP powder-actuated fastening tool It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. Parts of the tool DX 860-ENP powder-actuated fastening tool Cartridge loading channel Catch Base plate Grip and trigger mechanism Cartridge strip exit point Magazine Carrying handle Release button Fastener transport system Power regulation wheel Rotating sleeve Stop piece Wearing parts Piston with piston stopper Piston stopper 1. [. . . ] Press the nosepiece of the tool in slightly and turn the rotating sleeve through 90° (use the accessory scraper as an aid if necessary). 3. Carry out the steps described at 8. 2. 1 or 8. 2. 2. Turn the rotating sleeve subsequently back through 90° to its original position. en 21 8. Care and maintenance When this type of tool is used under normal operating conditions, dirt and residues build up inside it and functionally relevant parts are subject to wear. Regular inspections and maintenance are thus essential in order to ensure reliable operation. Recommended interval for cleaning the tool and checking the condition of the piston and piston stopper: At least daily when the tool is subjected to intensive use. After driving 5, 000 fasteners, at the latest. ­ Keep the dust or dirt away from foodstuffs. ­ Wash your hands after cleaning the tool. 8. 2. 1 Checking and replacing the piston and piston stopper -NOTE­ If the tool is used incorrectly (e. g. no fastener loaded in the tool before firing or the fastener is driven into unsupported sheet metal), the piston may become jammed against the piston stopper. Should the piston and piston stopper become fully seized in this way, these parts have reached the end of their life. The tool cannot be cycled when in this status. ­ The condition of the piston and piston stopper must be checked at regular intervals and at least daily. Stand the tool on its grip (upside down). Press the red button above the magazine and allow the fastener strips to slide out of the magazine. -CAUTIONParts of the tool may become very hot after a period of use. Protective gloves must be worn if the following maintenance procedure is carried out before the tool has been allowed to cool down. Unscrew the base plate with the fastener transport system in a counter-clockwise direction until it is released from the tool. Lift the base plate and fastener transport system away from the tool. Pull the piston out of the piston guide. Also pull the piston stopper out of the base plate (with the aid of the piston, if necessary). Check the piston and piston stopper for damage. [. . . ] In many countries, Hilti has already made arrangements for taking back your old powder-actuated tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tool as far as possible without the need for special tools. National and international directives and regulations must be observed. [. . . ]