User manual HILTI GX 100

[. . . ] Hilti Corporation FL-9494 Schaan Tel. : +423 / 234 2111 Fax: +423 / 234 29 65 www. hilti. com GX 100 Bedienungsanleitung Operating instructions de en Hilti = registered trademark of Hilti Corp. , Schaan W 2767 0203 25-Pos. 1 1 Printed in Liechtenstein © 2003 Right of technical and programme changes reserved S. & O. 338046 338046/B *338046* 1 2 3 1 10 11 2 14 1 1 3 GX 100 0 G 13 12 G 0 10 3 X 10 R GX 100 2 10 0 1 4 5 2 12 GX 100 2 X G X 13 11 3 GX 100 GX 100 0 G X 10 GX 100 GX 100 1 10 0 10 0 0 R G G X X R G X 10 0 G 10 GX 100 GX 100 1 2 GX 100 G GX 100 X 10 GX 100 X 10 0 9 9 6 GX 100 GX 100 GX 100 7 GX 100 GX 100 2 1 GX 100 1 2 GX 100 2 GX 100 GX 100 GX 100 3 2 X 1 G 2 4 5 GX 100 1 2 GX 100 1 3 1 8 7 6 3 4 GX 100 GX 100 0 0 R 8 9 14 R 15 GX 100 1 5 1 1 3 GX 100 GX 100 GX 100 3 1 2 2 GX 100 gas-powered fastening tool It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. [. . . ] 7. 3. 2 Setting the reduced fastener driving depth - NOTE This setting is suitable for fastening thin sheet metal to soft materials (e. g. Press the lockbutton and turn the nosepiece of the tool in the opposite direction to the arrow. Turn the nosepiece in the direction of the arrow until it engages. Press the lockbutton and turn the nosepiece of the tool in the opposite direction to the arrow. While pressing the lockbutton, pull the nosepiece away from the tool. -NOTE- en When holding the tool with the second hand, care must -CAUTIONNever attempt to redrive the same fastener. be taken to position the hand so that no ventilation slots or openings are covered. -WARNINGq q q Driving the nail may cause flying fragments. Flying fragments may injure parts of the body or the eyes. Wear eye protection and a hard hat. -CAUTIONq q q The nail is driven by the energy released on ignition of a gas-air mixture. An excessively high noise level may damage the hearing. Wear ear protection. -WARNINGq R GX 100 q q Making the tool ready to fire by pressing it against a part of the body (e. g. This could cause a nail to be driven into a part of the body. Never press the tool against a part of the body. 7. 1 Operation -NOTEThe magazine must contain at least 2 nails, otherwise no nail can be driven. Hold the tool at right angles to the work surface and then press it against the surface as far as it will go. Drive the fastener by pulling the trigger. 7. 2 The magazine -NOTEThe tool must be unloaded each time before the magazine is changed (see 7. 6). Bring the nosepiece lockbutton into alignment with the notch on the tool. Slide the nosepiece onto the tool into the desired position. Turn the nosepiece in the direction of the arrow until it engages. 7. 4 Support 7. 4. 1 Fitting the support 1. Push the support at right angles into the slot in the magazine. Pivot the support through 90° and engage it in position. Release the support by pressing the spring catch. Pull the support away from the magazine at right angles. [. . . ] Have the tool repaired at a Hilti repair center. Leakage from the gas can Faulty interface between gas can and Remove the gas can, remove the valve or leakage at the interface valve head head from the can and dispose of both between the can and the parts. Use a new gas can fitted with a valve head new valve head. Please send the tool to a Hilti repair center if these measures fail to remedy the problem. 22 10. [. . . ]