User manual HILTI HIT-ED 3500

[. . . ] 9 10 HIT-ED 3500 0 0 Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Gebruiksaanwijzing de en fr it nl pt es da fi no sv el pl ru sl cs hu zh ja ko ar 2x 11 12 Manual de instruções Manual de instrucciones Brugsanvisning 0 1 0 Käyttöohje Bruksanvisning Bruksanvisning Instrukcja obslugi Navodila za uporabo Návod k obsluze Használati utasítás Hilti = registered trademark of Hilti Corp. , Schaan W 3203 0107 00-Pos. 1 1 Printed in Liechtenstein © 2007 Right of technical and programme changes reserved S. & O. 273302 / E 273302 *273302* 1 2 0 3 1 1 1 2 1 2 4 5 Hilti HIT HY 150 123456 02/06 3 4 5 6 7 6 0 8 9 2 0 1 1 OK 3 +" + 7 8 +" +± 0 0 1 Hilti HIT-ED 3500 (12V) electric dispenser It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. [. . . ] b) Ensure that the workplace is well ventilated. Exposure to dust at a poorly ventilated workplace may result in damage to the health. 5. 2. 3 Safety equipment a) The user and any other persons in the vicinity must wear suitable eye protection and protective gloves while the tool is in use. a) Mobile generators may generate an excessively high voltage. Check that the mains adaptor is operated only within the specified voltage and frequency range. The mains adaptor may otherwise suffer damage. b) Check the condition of the supply cord and its plug connections and have it replaced by a qualified electrician if damage is found. Push the battery into the tool from below until it is heard to engage with a click. -CAUTION- A falling battery may present a risk of injury to yourself or others. Check that the battery is seated securely in the tool. This will ensure that the cells form correctly. Incorrect initial charging may have a permanent, negative effect on battery capacity. Please refer to the applicable battery charger's operating instructions for information about initial charging. 6. 2. 2 Charging a previously used battery -CAUTIONUse only the Hilti chargers listed under "Tools and accessories". Ensure that the outer surfaces of the battery are clean and dry before inserting it in the corresponding charger. Read the operating instructions for the charger for further information about the charging procedure. 6. 3 Fitting the battery -CAUTIONBefore fitting the battery, check that the tool is switched off and that the transport lock is engaged (selector switch in the neutral position). Use only the Hilti batteries intended for use with this tool (SFB 121 or SFB 126). 15 7. Operation Notes on use Important Observe the safety rules. Observe the information in the operating instructions for the various foil packs and the safety data sheets for chemical products. The cordless dispenser begins to operate when the trigger is pressed while the selector switch is in the single-stroke or continuous operating mode position. It must be ensured that the trigger is not activated during transport or storage of the tool, i. e. the selector switch must be in the left in the "0" (neutral) position in order to prevent battery drain and to ensure that no adhesive mortar is dispensed unintentionally. [. . . ] Batteries may explode if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or environmental pollution. Careless disposal may permit unauthorized and improper use of the equipment. This may result in serious personal injury, injury to third parties and pollution of the environment. -CAUTIONDispose of defective batteries without delay. [. . . ]