User manual HILTI PD22

[. . . ] PD 22 en Operating instructions *372188* 372190 1 9 2 I 3 6 5 4 PD LA SE R 22 MEN x 7 10 8 2 3 1 + x - - + I x MEN LA SE R PD 22 + - I Button functions PD 22 LASER Display Select menu Measure Calculate Switch on / off + I MENU x = Recall previous measurements (max. 3) Scroll through active menu MENU Show menu / exit from menu (rEF/nor/CONSt/Light/dELAY/bEEP/UNIT). 3) Scroll through active menu Measure distance or start tracking. x ­ x Addition Subtraction Multiplication Pythagoras (calculates opposite side of right-angled triangle) = I Execute calculation or reset display Switch range meter on / off PD LA SE R 22 MEN + I - x MEN + I - x + x - I The PD22 at a glance --- 3 1 2 I PD LA SE R 22 0. 1 - 30 m: PD LAS ER 30 - 100 m: 22 PD LAS ER 22 MEN MEN + ­ I + m ft in m ft in ­ m ft in x m ft in s MENU rEF + ­ + ­ + ­ + ­ + ­ + ­ + ­ nor CONSt Light dELAY bEEP UNIT nEAr/FAr 0. 000 . . . 999. 999m OFF / ON / Auto 0/2/5/10/20 s Auto/ON/OFF m / in + x - I + x - I x = m/m 2 /m 3 ft in sq. ft /in = a h! It is essential that the operating instructions are read before the range meter is operated for the first time. [. . . ] 7. 5 Taking measurements from various surfaces 7. 5. 1 Plants and trees It is not possible, as a rule, to take measurements from plants and trees, even over very short distances. Matt green surfaces decrease the range of the range meter. 21 7. Operation The measuring procedure is as described previously (see 7. 1). 7. 5. 2 Rough surfaces On rough surfaces (e. g. rough plaster), the measurement obtained is a weighted average, whereby the centre of the laser beam receives a higher weighting than the surrounding area. The measuring procedure is as described previously (see 7. 1). 22 7. Operation 7. 6 Continuous measurement (tracking) 1. Press the "measure" button once . The words «LASER TRACKING» are then shown in the display: LASER TRACK 3. Move the range meter to each new position and read off each distance as it is measured. 4. Tracking mode can be cancelled by pressing any button. 7. 6. 1 Continuous measurement «Tracking nEAr» When «Tracking nEAr» is activated, the shortest measured distance is always displayed (e. g. for determining whether objects lie parallel). 23 7. Operation Applications: ­ Determining the shortest distance between two objects without having to fix the point. ­ Determining a distance at right angles to a surface. Switch on the range meter and then press the MENU button. Select the nEAr function by pressing the ­ or + buttons. Aim the range meter at the target surface. Press the "measure" button. 6. The value displayed is updated continuously. Move the range meter until the lowest value is displayed (shortest distance). 24 7. Press the "measure" button again to stop measuring. [. . . ] Should you wish to return the machine or appliance yourself to a disposal facility for recycling, proceed as follows: Dismantle it as far as possible without the need for special tools. Separate the individual parts as follows: Part, assembly Casing, toolbox, target plate, carrying case, keypad Measuring module, electronics Screws, small parts Main material Recycling Plastic Various Steel Plastics recycling Electronics scrap Scrap metal * Dispose of batteries in accordance with national regulations. 37 12. Warranty Hilti warrants that the product supplied is free of defects in material and workmanship. This warranty is valid so long as the product is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, all warranty claims are made within 12 months from the date of the sale (invoice date), and the technical system is maintained. [. . . ]