User manual HILTI PM 10

[. . . ] Avoid unusual body positions when vrorking from ladders. Allvays stay in balance and make sure thai y0ur stance rs secure. Always leave the tool in its protective rubber housing when in use. [. . . ] The 3 type AA batteries (alkaline) have a life ol approx. 30 hours when the t0ol is used at n0rmal r00m temperature. 2. Technical data Horizontal accuracy a1 25 C (77'F) <t 3Inm @10 m within self-levelling range 14' Vefiical accuracy al25'C (17"F) vrithin sel{-levelling ranqe I 4 (<t114 inch @ 60 feet) <t 3 mm @ 10 m (<t114 inch @ 60 feet) 90'angle accuracy aI25"C (/7'F) <r3mm@10m (<1/4 inch (@ 60 feet) (o @ SelI-levelling tinre: <5sec Sell-levellinq range in x and y. !4 Laser diode 625-640 nm, Poiryer <1mW Laser class 2 product Class ll ir' Levelling beams (horizontal) 2, P[rmb line beam 0N/0FF switch 0N indicator/low battery warning i5l Alignment/positioning notches i6 1 /4"-20 lhread f0r mounting or llrackel 0n a trip0d Light source: Laser class as per lECB25- 1 /EN60825 z Battery compartment for three type AA batteries 2] CFR: :8. Rubller housing Weight including batteries. 360g(08pounds) 30 D imensions. 50 mm x 108 mm x 95 nrm 3. ltems supplied Inslrumenl only (2"x43"x3. 75") Distance from edge of housing to centre of laser beam: Batte ries: 25 mm (1") AA alkaline or AA Ni/Cd (3 balreries) Battery lile with 3 AA alkaline llatteries vrith 3 Ni/Cd batreries. Approx 30 h Approx. 7h Automatic cut-out: 0perating temperature: Storage temperature. After approx. 20 minutes -20'C to 45'C (-4"F to -40 C to 63 C (-40 F 11 3'F) io 145 F) Insulation class: lP54 not including battery conr pa rtme nt I Sailcloth case Ptvl10 2 3. Target plate 0perating instructions 5 Point locator 32 Set 4. Working with the PM10 The insulating sticker must be removed {r0m the battery c0mpartmenl belOre the tool is operated for the lirst time. W'W'ffiffi' . M rll Sailcloth case t. . 2) . q. . A. Set up the t00l 0n a stable surface or supp0rt. a) 0n the Iloor b) 0n a tripod c) 0n the magnetic bracket the lrame clamp Activate the 0N/0FF switch and then wait until the laser sp0t stabilises itsell 0n the target (< 5s). d) 0n , qw, Wall bracket Frame clamp 7t 8, 1 lf the laser sp0t 0n the target begins to blink. the tool must be rep0siti0ned h0rizontally (begins to blink when 0utside the sell-levelling range ol I 4"). B. Deviation from the horizontal/vertical line can then be read Jr0m the target plate, whereby the distance from the edge 0f the tool t0 the centre ol the beam c0rresponds to the distance lrom the edge 0{ the target plate t0 its centre (25 mm or 1 ") The markings on the housing are used to positi0n the tool. PN/1 O 3) a4) Target plate Carrying case Point localor 0perating instructions N, 4agnetic bracket !l , 5 34 Leve || ing Setling out right angles wffi Hffiffi -. ll . l(ffiw l, )A* . . Z, Z, Z z-, r=-_t u 1) ll t*r& i a' . 4 '+-. \-\ Aligning and plumbing Measuring oul inclinations slope ratio= *_ ?o. q =, gg 't I h=1. 5cm . . t:, . . . =0. 75o/o - -__d - 2oo cm ffi percent = O -Jt=1 5#q I 38 4. 1 Usino the accessories a) Frame clamp When using the Frame clamp (e. 9. at a door f rame), the magnetic bracket can be slid 0nto the stationary law 0f the clamp by way 0f the rail at the rear. The protective cover should be frtted over lhe magnet. ' | ? o: i '''' a:' , . . :- NI t_ 1" (25, 4mm) E'-+ b) Magnetic brackel tif+--S The protective cover should rem0ved frOm the magnets be{ore using the magnetic bracket. v, #. i'^\ , i't & c) Wall bracket Checking accuracy The wall brackel is used for mounting the PIVI 10 on a non-nragnetic surface. Screvrs or nails can be used to jasten the wall bracket t0 sLrrfaces 0f this kind. The PlVl 10 can be set Lrp on the wall bracket with the magnetic holder (protective cOver rem0ve0). The PM 10 is adjusted precisely be{ore it leaves our premises. as with all preci- si0n tools, its accuracy must be checked at regular intervals. [. . . ] This warranty is valid as long as the tool is 0perated and handled correctly, cleaned and serviced properly and in accordance with the Hilti 0perating Instructi0ns, all warranty claims are made within l2 months {rom the date 0f the sale (invoice date), and the technical system is maintarned. This means that only original Hilti consumables, c0mponents and spares may be used in the t001. This warranly provides the free-01-charge repair 0r replacenrent 01 delective pais only. [. . . ]