User manual HILTI TE 500-AVR

[. . . ] TE 500 / TE 500-AVR Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Lietoßanas pamåcîba Instrukcija Kasutusjuhend de en fr es it nl da no sv fi pt el lv lt et ar Hilti = registered trademark of Hilti Corp. , Schaan W 3256 0107 00-Pos. 1 1 Printed in Liechtenstein © 2007 Right of technical and programme changes reserved S. & O. 378616 / A 378616 *378616* 1 2 3 4 1 1 5 6 4 2 3 3 2/5 1 2 9 4 5 1 2 4 3 5 6 3 1 2 7:30 a. m 6 1 3/5 4 8 7 2 07 TE 500 / TE 500AVR breaker It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. [. . . ] Damaged supply cords or extension cords present a risk of electric shock. c) Dirty or dusty power tools which have been used frequently for work on conductive materials should be checked at regular intervals at a Hilti Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of the power tool, especially dust from conductive materials, may present a risk of electric shock. d) When working outdoors with an electric tool check to ensure that the tool is connected to the electric supply by way of a ground fault circuit interrupter (RCD) with a rating of max. Use of a ground fault circuit interrupter reduces the risk of electric shock. e) Use of a ground fault circuit interrupter (RCD residual current device) with a maximum tripping current of 30 mA is recommended. 5. 2. 4 Work area a) Ensure that the workplace is well lit. b) Ensure that the workplace is well ventilated. Exposure to dust at a poorly ventilated workplace may result in damage to the health. 21 c) If the work involves breaking right through, take the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or fall down and injure other persons. 5. 2. 5 Personal protective equipment tection, protective gloves and breathing protection while the power tool is in use. en The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear pro- 6. Slide the side handle clamping band over the chuck and onto the cylindrical section at the front end of the power tool. Pivot the side handle into the desired position. Secure the side handle by turning the knob. 6. 2 Unlocking the tool (theft protection system) NOTE See section "Using the TPS theft protection system". 6. 3 Use of extension cords and generators or transformers Please refer to section 2 "Description". 6. 1 Fitting and adjusting the side handle 2 1. Disconnect the supply cord plug from the power outlet. Release the side handle clamping band by turning the knob. 7. Operation 7. 1 Preparing for use CAUTION Wear protective gloves when changing insert tools as the insert tools get hot through use and they may have sharp edges. DANGER Always hold the power tool securely with both hands on the grips provided. Keep the grips dry, clean and free from oil and grease. 22 7. 1. 1 Fitting the insert tool 3 1. Disconnect the supply cord plug from the power outlet. Check that the connection end of the insert tool is clean and lightly greased. [. . . ] The power tool doesn't start and the indicator lamp blinks yellow. The power tool doesn't achieve full power. A fault has occurred in the power tool. The carbon brushes are worn. The power tool has not been unlocked (power tools with optional theft protection system). The extension cord's conductor cross section is inadequate. [. . . ]