User manual HILTI TE 7-A

[. . . ] 12 13 TE 7-A Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso de en fr es it nl da no sv fi pt el lv lt et 14 Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning 36 Volt Li-Ion 3. 3 Ah 36 Volt Li-Ion 3. 3 Ah Käyttöohje Manual de instruções Lietoßanas pamåcîba Instrukcija Kasutusjuhend Hilti = registered trademark of Hilti Corp. , Schaan W 3091 0706 10-Pos. 1 1 Printed in Liechtenstein © 2006 Right of technical and programme changes reserved S. & O. 202925 /A 202925 *202925* 1 2 3 7 1 1 2 43 2 1 2 2 1 1 3 4 3 4 1 8 1 36 Volt 2 2/5 1 1 3 5 6 7 8 5 4 1 2 5 3 6 9 1 1 2 43 2 3 4 1 1 6 3 36 Volt Li-Ion 3. 3 Ah 10 2 11 5 6 7 8 1/4 TE 7 A cordless rotary hammer It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. [. . . ] Push the insert tool further into the chuck until it is heard to engage. Check that the insert tool has engaged correctly by pulling it. Release the side handle clamping band by turning the handle counterclockwise. Pivot the side handle into the desired position. Adjust the depth gauge to the desired drilling depth. Tighten the side handle securely by turning the grip section. This also clamps the depth gauge in position. CAUTION In the event of the drill bit sticking, the power tool will pivot about its own axis. Always use the power tool with the side handle fitted and hold it securely with both hands so that the resulting opposing force causes the slip clutch to release in the event of the drill bit sticking. Use clamps or a vice to hold the workpiece securely. 7. 1 Preparing for use 7. 1. 1 Fitting the insert tool 5 CAUTION Wear protective gloves when changing the insert tool. Set the forward / reverse switch to the middle position or remove the battery from the power tool. Check that the connection end of the insert tool is clean and lightly greased. Clean it and grease it if necessary. 25 7. 1. 3 Removing the insert tool 7 CAUTION Wear protective gloves when changing insert tools as the insert tool will get hot during use. Set the forward / reverse switch to the middle position or remove the battery from the power tool. Open the chuck by pulling back the chuck release sleeve. 7. 1. 4 Removing the chuck 8 CAUTION Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury. NOTE Set the selector switch to the "Chiseling" position before removing the chuck. Set the forward / reverse switch to the middle position or remove the battery from the power tool. Pull the chuck sleeve forward and hold it securely. Remove the chuck by pulling it away from the power tool. 7. 1. 5 Fitting the chuck 9 CAUTION Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury. NOTE Set the selector switch to the "Chiseling" position before removing the chuck. [. . . ] The tool makes no progress. Possible cause The chuck is not pulled back fully. Remedy Pull the chuck back as far as it will go and remove the insert tool. The forward/reverse switch is set to Set the forward/reverse switch to reverse rotation. Disposal CAUTION Improper disposal of the equipment may have serious consequences: The burning of plastic components generates toxic fumes which may present a health hazard. Batteries may explode if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or environmental pollution. [. . . ]