User manual HILTI TE6-S

[. . . ] TE 6-S / TE 6-C USA CDN E P Operating instructions Mode d'emploi Instrucciones de uso Manual de instruções 1­ 9 11­19 21­30 31­39 369018 *369018* 1 UL listed to US and Canadian safety standards Homologué UL (conforme aux normes de sécurité américaines et canadiennes) Producto homologado según normas de seguridad americanas y canadienses Produto homologado de accordo com as normas de segurança americanas e canadianas C R US 2 3 3a TE 6-S 3b TE 6-C 4 5 6 R L R L 7 TE 6-C TE 6-S 8 9 10 11 12 TE 6-S/TE 6-C rotary hammer drill It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. General information 1. 1 Indication of danger -CAUTIONThis word is used to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. [. . . ] Keep the grip dry, clean and free from oil and grease. Hold the side handle tightly at its farthest end. 4. 6. 1 Mechanical hazards V ~ Hz A n0 /min k . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . volts alternating current hertz amperes no load speed revolutions per minute diameter protective earth plug 4. 8 Wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. Check that the insert tools used are compatible with the chuck system and that they are secured in the chuck correctly. Functional description The TE 6-S / TE 6-C rotary hammer drills with selectable pneumatic hammering mechanism are electrically-powered tools for drilling in concrete, masonry, plasterboard (drywall), wood, plastics and metal. The TE 6-C features an additional chiselling function suitable for light-duty chiselling work. The tools are designed for professional use. Concealed electric cables, gas and water pipes present a serious hazard if damaged while working. Accordingly, check the working area in advance, e. g. Avoid body contact with earthed objects such as pipes or radiators. External metal parts of the 4 Chuck ­ with rotary locking action ­ Interface for TE-C chuck and keyless chuck Switches ­ Speed-control switch ­ Function selection switch TE6-S: 3 drilling functions TE6-C: 2 drilling functions and 1 chiselling and adjusting function ­ Reversing switch (switch for forwards/reverse rotation) Side handle ­ Privoting side handle with depth gauge Lubrication ­ The gearing section and hammering mechanism feature permanent grease lubrication. Secure the side handle by turning the side handle grip. Assembly The tool must not be connected to the electric mains supply. Release the side handle clamp by turning the side handle grip. Slide the side handle / clamping band over the chuck onto the housing (clamping groove). Turn the side handle into the desired position. Secure the side handle by twisting its grip. 6. 2 Changing the chuck Removing the chuck 1. Pull the sleeve back and hold it in this position. Place the chuck on the guide and release the sleeve. Rotate the chuck until the sleeve engages. 7. 4 Hammer drilling with full hammering action (TE6-S / TE6-C) 3a 3b -CAUTION The material may splinter during drilling. Splintering material may injure parts of the body and the eyes. [. . . ] When holes are to be drilled to a precise depth, e. g. for setting anchors, the hole depth must be checked by drilling test holes. Pull back the rib (G) on the rear of the suction head (7). Pull the old suction head upwards out of the guide (H). [. . . ]