User manual HITACHI 13GA1BA

[. . . ] WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. CAUTION This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to incorrect handling. Please refer to the pages written following this symbol. NOTE · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual. [. . . ] (40) Using the buttons / switches the language of menu. See the item LANGUAGE of section SCREEN menu. (36) Pointing at the "Go To Advance Menu" and pressing the button changes the EASY MENU into the Advance MENU. (23) Performs to use the menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION. RESET FILTER TIME LANGUAGE Go To Advance Menu 7 Multifunctional settings PICTURE menu With the PICTURE menu, items shown in the table below can be performed. Choose an item using the cursor buttons / on the projector or remote control, and press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item BRIGHT CONTRAST Description Using the buttons / adjusts the brightness. : Using the buttons / adjusts the contrast. : Light ó Dark Strong ó Weak GAMMA #1 #2 DEFAULT CUSTOM DEFAULT CUSTOM DEFAULT CUSTOM MENU [RGB1] PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU :SELECT BRIGHT +0 CONTRAST +0 GAMMA DEFAULT 1 COLOR TEMP HIGH COLOR +0 TINT +0 SHARPNESS +0 PROGRESSIVE TURN OFF MY MEMORY SAVE 1 Using the buttons / switches the GAMMA mode. # DEFAULT ó # CUSTOM ó # DEFAULT #3 CUSTOM ó #3 DEFAULT ó # CUSTOM To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM Selecting a mode of CUSTOM and then pressing the button or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones. Choose an item using the buttons /, and adjust the level using the buttons /. Performing the LOAD, LOAD, LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command's number, and adjusts the picture automatically depending on the data. Performing the SAVE, SAVE, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command's number. PROGRESSIVE MY MEMORY 30 Multifunctional settings IMAGE menu With the IMAGE menu, items shown in the table below can be performed. Choose an item using the cursor buttons / on the projector or remote control, and press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description Using the buttons / switches the mode for aspect ratio. At a RGB signal 4:3 ó 6:9 ó NORMAL At a video signal / no signal 4:3 ó 6:9 · The NORMAL mode keeps the original aspect ratio of the signal. · At a HDTV component video signal of 5i (080i) or 750p (70p), this item can't be chosen. · Performing the automatic adjustment initializes the aspect ratio setting. Using the buttons / adjusts the over-scan ratio. Large (It reduces picture) ó Small (It magnifies picture) · This item can be chosen only at a video signal. · When this adjustment is too large, certain degradation may appear at the frame area of the picture. · The number displayed on the menu during this adjustment is just for your reference , and might not be exact display ratio. [. . . ] After the treatment, resent the power to ON. It is time to clean the air filter. Lighting In Green Simultaneous blinking in Red Please immediately turn the power OFF, and clean or change the air filter by referring to the section "Air Filter". After cleaning or changed the air filter, please be sure to reset the filter timer. After the treatment, resent the power to ON. NOTE · When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the "" (OFF) side of the power switch, and wait at least 45 minutes. [. . . ]