User manual HITACHI 28LD5200E

[. . . ] Colour LCD Monitor Model PW1L 28LD5200E USER'S MANUAL MANUEL UTILISATEUR BEDIENUNGSANLEITUNG READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS. The ENERGY STAR® emblem does not represent EPA endorsement of any product or service. [. . . ] Adjust it depending on the user's preference. This features the spacious sound effects of a stadium. This will automatically adjust volume so each channel and input has the same average volume level. The original factory settings for the items of this Menu page can be restored by pressing the OK button. Audio Mode Favourite Treble Bass Balance Suppresses treble. Suppresses right-side sound. Enhances treble. Suppresses left-side sound. SRS TruBass Matrix Surround Perfect Volume Reset Off Low Middle High Off Off (off the function) On On (waiting to reset) TIMER MENU Picture Audio Timer Function Setup Language Select OK Set Timer Off Timer On Timer Select : 30Min. : --:-Return OK MENU P+ Adjust P- Selected characters M M Setup hint This function automatically sets the power to standby status when the indicated time period has elapsed. This automatically sets the power from standby to ON when the indicated time period has elapsed. Input the required time by SELECT buttons on the remote control. Off Timer --Min. 90Min. --(:--) hours (- - : )- minutes On Timer 19 FUNCTION MENU Picture Audio Timer Function Setup Language Select OK Set Function Screen Saver Screen Wipe Black Side Panel Video Power Save Freeze Mode Default Zoom Reset Select Set Off On 60Min. Off Off Split Panoramic Reset Return OK MENU P+ P- P+ P- Function Wide Standard Setting Mode Display ID Number Reset Fill Off 1 Reset Select Set Return 20 M M OPERATING INSTRUCTIONS (continued) ENGLISH Horizontal Position Next / Prev Adjust P+ SETUP MENU MENU P+ P- Picture Audio Timer Function Setup Language Select OK Set P+ OK P- Setup Auto Adjust Horizontal Position Vertical Position Horizontal Clock Clock Phase Reset Select Return Adjust 0 + 31 ­ 20 10 Reset Exit OK 0 Return P+ P- P- Setup Auto Adjust Horizontal Position Vertical Position Horizontal Clock Clock Phase Reset Select Return Adjust 0 + 31 ­ 20 10 Reset Exit OK Clock Phase Next / Prev P+ 10 Adjust Return P- Setup Input Level Frequency Display WVGA Type WXGA Mode Vertical Filter Frequency Mode RGB1 RGB2 Select Set 0. 7V Off Off Off On Movie DVI-PC RGB Return * Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them. M M 21 LANGUAGE MENU Picture Audio Timer Function Setup Language Select OK Set Language OK MENU P+ P- English Français Deutsch Español Italiano Norsk Svenska Select Return Exit Select a language by M L SELECT buttons and press the OK button. OTHER FEATURES Automatic Store Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below. · The previously recorded items will be lost. · The signal mode can be identified by the horizontal/vertical sync frequency and the sync signal polarity. Different signals with which all the elements are the same or similar will be handled as the same signal. 22 OTHER FEATURES (continued) ENGLISH RGB2 RGB H : 48. 4kHz V : 60. 1 Hz OFF ON Signal Check Changes in the signal status are displayed on the screen as they arise. Status The input signal is switched or when the RECALL button is pressed. Display A guide is displayed for the input terminal and the horizontal and vertical sync frequency. Action RGB -- -- Min. -- -- : -- -- When the sync signal is no longer detected. · A guide displays No Sync. Recheck the personal computer Signal, and Power Save (for power switch status and the approx. · When the condition continues where the sync signal cannot be detected, indicator lamp of power source changes in orange and the mode switches to power save mode. Recheck the input signal specifications. !Signal When the input signal does not match the monitor specifications or is in an unstable status. 51 52 !Invalid Scan Freq. Power Save Mode When the RGB, RGB2 input is selected · When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the computer is not being used to reduce power consumption by this unit. Horizontal Vertical PC signal Operation mode Indicating lamp Power consumption Yes Yes Active (normal display) On Lights green 155W No Yes Yes No Blank (no display) Off Lights orange 1W or less No No RGB sync signal Returning to operating status · Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control. 23 NOTES About screen defects · High precision technology is used in the making of LCD panels but there may be dark spots (points that do not illuminate) and bright spots (points that are too bright) in some cases. [. . . ] Data3+ Pin 14 15 16 17 18 19 20 21 22 23 24 Input signal +5V Power Ground (for+5V) Hot Plug Detect T. M. D. S. Clock- 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Frame GND RGB terminal (D-sub 15-pin connector) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Input signal R (PR/CR) G or sync on green (Y) B (PB/CB) No connection No connection R. GND (PR/CR, GND) G. GND (Y, GND) B. GND (PB/CB, GND) No connection GND No connection [SDA] H. [V. CLK] [SCL] 5 4 10 15 14 3 9 13 2 8 12 1 7 11 6 · When different kinds of input signals are simultaneously input to the monitor via a graphics board or the like, the monitor will automatically select the signals in the following priority order: Sync signal type H/V separate sync. sync. on Green * Priority 1 2 3 *Even in the case of the recommended signals shown on the following page, there may be instances when correct display is not possible. [. . . ]