User manual HITACHI 32HDT20

[. . . ] PLASMA TELEVISION AVC (Audio/Video Control Center) & Plasma Display Monitor 32HDT20 OPERATING GUIDE 42HDT20 IMPORTANT SAFETY INSTRUCTIONS Video Audio Ch. Manager Locks Setup Move SEL 2-3 Sel FIRST TIME USE STB R WE PO CB D AR VCR UR SO TV CD WIZ CE TAP E L AM P 4-23 3 2 6 5 4 7 B DVD 1 9 O INF 8 0 NE A/V EP E MOD ECT ASP T TV/ RG SLE EXIT MEN AN CH ECT SCHD SEL GUIDE VO MUTE SVCS LAST L VID EZE FRE VCR PLUS+ VID 3 CH AC PIP AP VID 1 VID 2 PIP S EO CES VID PIP DE MO PIP SW THE REMOTE CONTROL CL U57 23 TS I 24-39 T U CH /TV 4 VID 5 REC Video Audio Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY USING THE RGB INPUT OF THE PLASMA TV 40-63 Sel 64-74 USEFUL INFORMATION INDEX 75-82 IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI PLASMA TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI Plasma Televisions. Safety is also foremost in our minds in the design of these units. [. . . ] The CBL button light will flash 3 times if the code was accepted. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box if the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code. The remote will now control your Cable box. TV POWER 5. 6. VCR CBL STB NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. The LAST CH button will act as the cable box ENTER button if required. The SLEEP button will act as your cable box `100' button if required. The ANT button will act as the TV/STB button when in STB mode. CABLE (CBL) button This button allows the remote to control your cable box by setting it to CABLE mode. PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. EXCLUSIVE TV buttons These buttons are for operating the TV. SOURCE WIZARD CD DVD TAPE AMP 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT TV/RGB A/V NET ASPECT MOD E 3. ME NU EX IT VOL SELECT CH 4. SV CS MUT VCR PLUS + E CH LAST GUIDE/ TV SC HD 5 VID 1 VID VID 2 5. VID 3 VID 4 PIP PIP CH FREEZE PIP MODE PIP ACCESS SWAP VIDEO 6. REC CLU-5723TSI MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 35 STB R POWE CBL RD VCR SOUR TV CD WIZA CE TAPE AMP 3 2 6 5 4 7 B DVD 1 9 INFO 8 T MODE 0 NET A/V P ASPEC SLEE EXIT CH T SCHD SELEC GUIDE/TV VOL MUTE SVCS VID ZE FREE VCR PLUS+ VID 3 CH ACCE PIP SS VID 1 VID 2 PIP VIDEO PIP SWAP MODE PIP REC 3TSI -572 CLU USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS TV/RG MENU ANT LAST CH Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote command set of your set-top-box/satellite systems. Turn ON your set-top-box/satellite systems. Aim the remote control at the front of your set-top-box/satellite systems. Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode. Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as shown on page 39. [. . . ] . AC 120V, 60Hz Power Consumption - Refer to rear panel at the back of the Plasma Monitor and AVC Center Antenna input impedance . . 1. 0Vp-p, 75 Ohm S-Video Luminance (Y) . . 0. 286Vp-p, 75 Ohm Component Video Luminance (Y) . . 0. 7Vp-p, 75 Ohm Audio input Impedence . [. . . ]