User manual HITACHI 32LD8A20A

[. . . ] LCD Colour Television LCD-Farb-TV-Gerät Télévision Couleur LCD Televisor Color LCD Digital Televisão a cores LCD LCD színes televízió Instructions for use Bedienungsanleitung Notice d'utilisation GB D F E PT HU 32LD8A20 32LD8A20 A Manual de Instrucciones Televisão a cores Használati útmutató Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear View and Peripheral Connections . . . . . . [. . . ] · Do not place the remote control under the direct sunlight or near sources of excessive heat. Connections to the Aerial Input Socket · Connect the aerial or cable TV plug to the Aerial input socket located at the rear of the TV and connect the cable plug coming out from the TV out socket located on the devices (VCR, DVB etc. ) to this socket as well. Operating Range for the Remote Control · Point the top of the remote control toward the LCD TV's remote sensor LED while pressing a button. 75 VHF/UHF CABLE TV REAR OF THE TV Inserting Batteries in the Remote Control Handset WARNING : Remote control is battery included. A plastic protector is used to disconnect the batteries in order to prevent the battery life from reducing. Please remove the plastic protector before the first use. · Remove the battery cover located on the back of the handset by gently pulling backwards from the indicated part. · Insert two AAA/R03 or equivalent type batteries inside. Place the batteries in the right directions and replace the battery cover. 30 30 SOUN D PICTURE FEATURE INSTA L L WIDE PC GUIDE 1 ABC 2 DE F 3 G HI 4 JK L 5 M NO 6 PQ R 7 STU 8 VW X 9 YZ P<P 0 -/-EXI T TV DT V V A I II RC 1072 Remote range is approximately 7m/23ft. English - 8 - Switching the TV ON/OFF To switch the TV on Your TV will switch on in two steps: 1- Connect the power supply cord to the system. Press Power On/Off button. Then the TV switches itself to stand-by mode (Optional). 2- To switch on the TV from stand-by mode either: Press a digit button on the remote control so that a programme number is selected, or Press the "-P/CH" or "P/CH+" button on the TV or press the "P-" or "P+" button on the remote control, so that last mode switched off is selected. By either method the TV will switch on. Initial Settings When the TV is turned on for the first time, Auto Programme menu will be displayed on the screen Because this is the first time the TV is used, there are no channels stored in the memory and the following message appears on the screen. Auto Program Country Language TXT Language To switch the TV off · Press the " (stand-by)" button on the remote control or On/Off switch on the TV, so the TV will switch to stand-by mode. To power down the TV completely, press Power On/ Off button or unplug the power cord from the mains socket. PLEASE CHECK ANTENNA CABLE AUTO. PROGRAMMING SYSTEM Ok UK Cancel Navigating the Menu System TV DTV VA I II For navigation For displaying menu options To confirm choices By pressing or button, adjust the Country item to highlight "Language" item. Use and press or button to set "Language". Use or buttons to select "TXT Language" and set it by using or buttons. Press "OK" button to continue: For more information on this process, see "Install Menu" section. Basic Operations You can operate your TV using both the remote control and onset buttons. 1- Press M to display the menu. 2- Press " " or " " button to select an icon. 3- Use " " or " " button to highlight. 4- Press " " or " " buttons to change the settings. 5- To exit the menu or return from sub-menu screen, press M. These explanations are available for the navigation of the whole Menu System. To select options that are explained in the following parts, refer to "Navigating The Menu System". Operation with the buttons on the TV Volume Setting · Press " -" button to decrease volume or " +" button to increase volume, so a volume level scale (slider) will be displayed at the middle of the bottom on the screen. Programme Selection · Press "P/CH +" button to select the next programme or "P/CH -" button to select the previous programme. Entering Main Menu · Press the "MENU" button to enter Main menu. In the Main menu select sub-menu using "P/CH -" or "P/CH +" buttons and enter the sub-menu using -" or " +" buttons. To learn the usage of the " menus, refer to the Menu System sections. English - 9 - AV Mode Press the "TV/AV" button at the control panel on the the TV to switch your TV to AV modes. Menu System Picture Menu Operation with Remote Control The remote control of your TV is designed to control all the functions of the model you selected. [. . . ] Did you perhaps interrupt the sound, pressing the button?Sound is coming from only one of the speakers. Is the balance set to one extreme?See Sound menu. Remote Control Your TV no longer responds to the remote control. If so you can still use the local buttons at the bottom of the TV. English - 19 - Appendix A: PC Input Typical Display Modes The display has a maximum resolution of 1360 x 768, frequency range of 56-75 Hz. [. . . ]