User manual HITACHI 32PD5200

[. . . ] Colour Plasma Display Monitor Model PW1 32PD5000 42PD5000 42PMA500 CMP4214E USER'S MANUAL MANUEL UTILISATEUR BEDIENUNGSANLEITUNG Th is It mo ca d n el ho is w no ev t er cla ac ss ce ed pt a 10 s H 80 D i 5 Re 0 ad si y gn b al ec s au an s d ei di t c sp a la nn y ot Ha Dc m ce at pt er a ia s l i ig n na th l is of fo 72 rm 0 at p 5 . 0. System Name 32PD5000/42PD5000 32PD5100/42PD5100 32PD5200/42PD5200 READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS. [. . . ] · No picture with the power indicating lamp lights in orange. !· Check the way the signal cable is connected. · Make sure that the switch of the computer, imaging equipment , etc. , is turned on. · Make sure the computer is not in the power-save mode. · Check to see if the input selection matches the connection terminal. An input signal is not received normally. · Check to see if the input signal matches the monitor specifications. · Check the way the signal cable is connected. 11 · The message "Invalid Scan Freq. " is displayed. 11 28 29 !Invalid Scan Freq. · The power indicating lamp is normally lit but no picture . · Check the contrast and brightness settings (adjust them for higher contrast and brightness). · Check the way the signal cable is connected. 11 17 · The display image appears flowing slantwise. · Text displayed across the screen appears vertically streaked, with the characters in vertical columns blurred. · Text displayed across the screen appears blurred. · A fine pattern flickers when displayed on the screen. · The remote control does not work. · Adjust the dot clock frequency and phase. (Adjust the dot clock frequency first, the dot clock phase next. ) (RGB input) 20 26 · Adjust the dot clock phase for the clearest viewing. (RGB input) 20 26 · Check to see if the batteries are loaded in the remote control in opposite direction. · Check to see if the batteries in the remote control are OK. 9 24 Symptom · The temperature of the display panel surface is high. Point to check · The plasma display panel is lighting the phosphors by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction. · High-precision technology is used to manufacture the plasma display panel, However in some cases, there are minor defects in some parts of the screen. Please note that this is not a malfunction. See page - · There are locations on the screen that are different from the periphery (*). *Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc. [. . . ] Place a protective sheet cover on the top of a table and place the plasma TV on the cover with the back side upward. (for CL32-PD2100 only. ) Remove the 4 or 5 (CL37-PD2100) screws fastening the stand and remove the stand in the direction indicated by the arrow mark. Remove the 4 screws Remove the 4 EMI ground screws. (CL32-PD2100) 2. Installing the TV-mount metals CL32-PD2100 Fasten the two TV-mount metals to the back of the plasma TV with 4 M6 x 18 screws. 4 M6 x 18 screws TV-mount metal Plasma TV The 3rd TV-mount metal hole Remove the screws (CL37-PD2100) Table Stand Protective sheet cover The 4th TV-mount metal hole ­6­ CL37-PD2100 Fasten the bracket (R) , (L) to the TV mount metal with 4 M6 x 18 screws. TV-mount metal 4 M6 x 18 screws Fasten the two TV-mount metals to the back of the plasma TV with 4 M6 x 18 screws. 4 M6 x 18 screws Bracket (R), (L) Bracket The 1st TV-mount metal hole CL42-PD2100 Fasten the two TV-mount metals to the back of the plasma TV with 4 M6 x 18 screws. The 2nd TV-mount metal hole The 5th TV-mount metal hole Installing the plasma TV on the wall mount Hang the TV-mount metal catches on the wall-mount unit cutouts. Fasten with 2 M6 x 18 screws from the bottom. [. . . ]