User manual HITACHI 42PD7800

[. . . ] USER'S MANUAL 32PD7800 42PD7800 Thank you very much for purchasing the HITACHI Plasma Display. Before using your monitor, please carefully read the "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to operate the monitor properly. You will find it useful in the future. Notes on lnstallation Work: This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. [. . . ] · Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. And then, pressing the MULTI PICTURE button again will display the 12 pictures again. · Pressing the MULTI MODE button at the 12 picture mode will display the 2 pictures (Split) mode. · This function is not provided for AV monitor model. 1 2 3 4 5 6 7 8 9 10 11 12 27 ENGLISH OPERATING INSTRUCTIONS (continued) Displaying MULTI PICTURE (continued) Activating the Split mode from the video input screen Pressing the MULTI PICTURE button one time will display 2 pictures. · The speaker icon can be shifted left and right by pressing the and SELECT buttons. The audio of the video will be output from the side on which the speaker icon is located. · The same video input mode cannot be selected for both screens at the same time. · Pressing the MULTI PICTURE button again will cancel the 2 pictures display. · Refer to the table for 2 pictures (Split) mode. AV1 AV2 Activating the MULTI PICTURE mode from the RGB input screen Pressing the MULTI PICTURE button one time will display 2 pictures. · This mode can be available from RGB1(DVI-PC) and RGB2(RGB) input. · The speaker icon can be shifted left and right by pressing the and SELECT buttons. The audio of the video will be output from the side on which the speaker icon is located. · The sub-screen position can be selected up and down by pressing and SELECT buttons. · The sub-screen can be selected with the AV1 AV6, TV channel buttons from the status that the speaker icon appears on the left side of AV etc. · Pressing the MULTI PICTURE button again will cancel the 2 pictures display. · "Frequency Mode" in the Setup Menu should be set to Movie when sub-screen is the component signal of 1080i/50 or 1080i/60. AV1: Displays the VIDEO input signal of the sub-screen. RGB2 AV1 (Subscreen) NOTE · Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change to power save mode. · Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time. 2 Pictures (Split) Input terminal Sub Main AV1 AV5 AV1 AV2 AV6 RGB1 RGB2 TV PAL, SECAM NTSC3. 58/4. 43 576i, 576p 480i, 480p 1080i/50 1080i/60 720p/60 STB Component ( : Available) Teletext is available only for TV TV AV1 AV5 AV1, AV2, AV6 RGB1 RGB2 Component TELE TEXT Main Sub PAL NTSC3. 58 576i 480i 1080i/50 1080i/60 720p/60 STB SECAM NTSC4. 43 576p 480p 4 Pictures Input terminal Sub Main TV PAL, SECAM NTSC3. 58/4. 43 576i, 576p 480i, 480p 1080i/50 1080i/60 720p/60 STB Component ( : Available) TV AV1 AV5 AV1, AV2, AV6 RGB1 RGB2 Component TELE TEXT Main PAL NTSC3. 58 576i 480i 1080i/50 1080i/60 720p/60 STB SECAM NTSC4. 43 576p 480p Sub 1 Sub 2 AV1 AV1 AV2 AV6 RGB1 RGB2 Sub 3 28 OPERATING INSTRUCTIONS (continued) ENGLISH [Split] 5 FREEZE button Picture Freezing When the FREEZE button on the remote control is pressed, the screen transfers into the freeze mode. · There are two types of freezing screen mode, Split and Strobe. These are possible to select at the "Freeze Mode" setting of the Function Menu. · The Split mode will display 2 pictures from the same source on the screen with one active picture and the other still. · The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still. · Pressing the FREEZE button again changes the screen back to the normal picture. · This function is also available from video input mode besides TV mode. Refer to the table for Freeze function [Strobe] 1 as below: Split TV PAL, SECAM NTSC3. 58/4. 43 576i 480i 576p 480p 1080i/50 1080i/60 720p/60 RGB, DVI-PC ( : Available) Strobe 5 A B 2 3 4 6 7 8 9 10 11 12 Active 29 OPERATING INSTRUCTIONS (continued) ROTATE button PHOTO button SLIDE SHOW button PHOTO INPUT button Photo Input Display (37/42 only) With the PHOTO button on the remote control, the pictures from a digital camera or Card Reader can be displayed. Digital Camera USB cable USB Card Reader Operating the Photo Input 1. Make sure that the power switch of the monitor is turned off/standby before using. [. . . ] 8) Press the SELECT button and select Horizontal Clock. (Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment. ) 9) Press the or ADJUST buttons and search for clear characters over the entire screen. 10) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen. · The display image may be momentarily disturbed during clock adjustment but this is not a failure. Symptom 2 Text displayed across the screen appears blurred in its entirety (Figure 2). A fine pattern flickers when displayed on the screen (Figure 3). [. . . ]