User manual HITACHI 42PD8700C

[. . . ] Instructions for use Bedienungsanleitung GB D F I 42PD8700C Notice d'utilisation Istruzioni per l'uso Contents Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 2 PLASMA TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Before Switching On Your TV . . . . . . . . . . . . . . . . . 8 Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connections To The Aerial Input Socket . . . [. . . ] The digital TV Setup menu screen is accessed from the Main Menu. Press the " " button to display the Main Menu and use or buttons to highlight "TV Setup". Press " OK" button to display TV Setup menu screen. · Here the six settings of channel type, channel name, start time, end time, date and frequency mode can be set. You can move freely between each setting using or buttons. or but· The channel type is set using tons. It enables displaying only the selected type channels. · The channel name is set using or buttons to display the channel which broadcasts the programme. · The start time, end time and date are each set with the number buttons on the remote control in 24-hour format. · The frequency mode determines how often the receiver operates this event and is set with the or buttons to be either Once, Daily, or Weekly. Press OK button to complete setup. Main Menu Channel List Installation Configuration Timers TV Setup Common Interface Detailed information for all menu items is in AnalogueTV Menu System section. Hint If an invalid number for the start or end times or the date is entered, "Entered time is not valid" message appears on the menu. Common Interface · Press " " button to display the Main Menu and use the or buttons to highlight the "Common Interface" line and press "OK" button. RECORDINGFROM IDTV Connect your VCR to AV2 via a scart lead. Set the AV2-OUT in the feature menu to DDT, as illustrated and described on page 24. Set your TV to standby using the remote control. Set your VCR to correspond with the time set on your TV and select external input (refer to your VCR instruction book). If you switch on your TV whilst the timer recording is active and then switch back to Main Menu Channel List Installation Configuration Timers TV Setup Common Interface It is required to subscribe to a pay channel company to view the pay channels of the Digital Terrestrial broadcasting. - 20 - Obtain the Conditional Access Module (CAM) and the Viewing card by subscribing to a pay channel company, then insert into the Television using the following procedure. Switch off the TV and unplug from the mains. Insert the CAM, then Viewing Card to the slot that is located in the terminal cover at the left-hand side of the TV (from front view). · The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. · Some CAMs may require the following set up. Please set the CAM by entering the IDTV menu, Common Interface then pressing "OK" button. (CAM set up menu is not displayed when it is not required. ) · To see the viewing contract information: Enter IDTV; press " " button, then highlight Common Interface and press "OK" button. [. . . ] These leads can be purchased from your Hitachi dealer or any good High Street electrical retailer. . . . or through a satellite decoder. . . PLASMA TV GB Aerial RF Lead from Satellite to TV · Scart Lead to EXT-1 on TV. TV ANT. IN VCR RF Lead to Aerial Satellite LNB lead . . . or through a VCR and satellite decoder. PLASMA TV RF Lead from VCR to TV · Scart Lead to AV-1 on TV. RF Lead from Satellite to VCR Aerial TV ANT. IN VCR RF Lead to Aerial Satellite LNB lead ANT. IN AV-1 AV-2 VCR connect the TV plug to the mains socket GB European plug UK plug Power Cord Power on/off Input button Plug the mains lead into the TV. . . insert plug. . . . . . and switch on insert plug. . . switch your TV on by pressing the On/Off button Front View NB: When the set is first switched on, the set will be in standby and the indicator on the front of the set will illuminate red. Press the channel up down (P- , P+) or numeric buttons (1, 2, 3, . . . ) to operate. basic functions of remote control TV DTT/TV DVD SAT AV1 AV5 AV2 RGB1 SEL AV3 RGB2 AV4 To enter the main menu For navigation of the menus MENU To return to previous menu OK S. MODE P . MODE I/II Volume Up/Down* P Programme Up/Down* 1 4 7 2-4-12 2 5 8 0 3 6 9 To select a programme number. GUIDE SLIDE SHOW-ROTATE . . . . SWIVEL PHOTO *Also used for navigation in menus important note before starting Auto Setup If you have a Video Cassette Recorder or a Satellite receiver connected to your TV please ensure that they are switched on before automatic tuning begins. In the case of a VCR, insert a pre-recorded tape and begin playback of your equipment. These measures ensure that all your external equipment is tuned in during the Auto Setup procedure. GB GB start A. P. S. [. . . ]