User manual HITACHI 46UX17K

[. . . ] IMPORTANT 1 HITACHI PROJECTION COLOR TV 60SX8B/9K 50SX6P 50UX18B/19K 46UX16B/17K OPERATING GUIDE TABLE OF CONTENTS IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY TIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PICTURE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Set the MULTI-PAGE select switch to "CATV". Set the USE/LEARN mode select switch to "USE. " 3. Aim the Genius Remote control at the front of your cable box. While holding down the SELECT button, press the button that matches our cable box as shown on page 25. The channels of the cable box will begin changing when the correct button is pressed. When this occurs, the Genius Remote Control is programmed for your cable box. If the cable box channels do not change after 5 seconds, try a different Genius Remote button. Release both buttons when the cable box starts to change channels. The Genius Remote will now control your cable box. Click here to see the CLU-850GR in the CATV position. If your cable box cannot be operated after performing the above procedures, this means that your cable box codes have not been precoded into the GENIUS REMOTE. Please store your cable box codes in memory by using the USER mode. The GENIUS REMOTE CONTROL will remember the codes you have programmed in until the batteries are removed from the GENIUS REMOTE CONTROL. After replacing the batteries repeat the entire programming procedure stated above. PRECODED FOR CABLE BOX These buttons always transmit the chosen precoded CATV codes. SELECT BUTTON This is for setting up the cable box's Pre-code. EXCLUSIVE TV BUTTONS These buttons are for operating the TV. 30 VCR AND CABLE BOX CODES VCR AND CABLE BOX CODES TABLE 1. VCR Precoded remote controls Press SELECT and this VCR BRAND button Audio Dynamics VOLUME Canon 6 Citizen 0 Craig VOLUME Curtis Mathis 2/6 dbx VOLUME Dimensia 2 Emerson 100/ENTER Fisher VOLUME GE 2/6 Goldstar 0 Hitachi 1 Instant Replay 6 JC Penny 1 / 6 / 9 / VOLUME JVC 0 / VOLUME Kenwood 0 / VOLUME Magnavox 4/6 Marantz 9 / VOLUME Marta 0 Memorex 6 / VOLUME MGA 7 Minolta 1 Mitsubishi 7 Montgomery Wards CHANNEL NEC 9 / VOLUME Panasonic 6 Pentex 1 Philco 4/6 Philips 4/6 Pioneer 1 ProScan 2 Quasar 6 RCA 1/2 Realistic 6 / 9 / CHANNEL / VOLUME Sanyo 9 / VOLUME Scott 7/8 Sears 1/9 Sharp CHANNEL Sony 5 / MUTE / AVX Sylvania 4/6 Tashiko 0 Technics 6 Toshiba 1/8 Vector Research VOLUME Video Concepts VOLUME Wards CHANNEL Yamaha 0 / VOLUME Zenith 3/5 31 VCR AND CABLE BOX CODES TABLE 2. Cable Box Precoded remote controls Press SELECT and this CATV brand button General Instrument 0/1/2/3 Hamlin 4 Jerrold 1/2/3/3 Magnavox 9 Panasonic 8 Philips 9 Pioneer 7 Regal 4 Scientific Atlantic 6 Viewstar 9 Zenith 5 32 USING THE GENIUS REMOTE TO LEARN ADDITIONAL FUNCTIONS USING THE GENIUS REMOTE TO LEARN ADDITIONAL FUNCTIONS The Genius Remote is equipped with a learning function which allows it to learn additional infrared control codes. This remote will not only control the television, a VCR, and a cable box, but also other electronic equipment which uses an infrared remote transmitter, by learning the transmitter's codes. Only infrared remote control codes can be stored in memory. Before starting the memory operation Since the infrared signals sent from the remote transmitter may be reflected by a wall, door, etc. , even if the transmitter is not pointed directly at the device, it may operate. [. . . ] The labor to repair or replace will be at no charge during the one year warranty duration. Labor charges to repair or replace lenses found to be defective after the one year warranty duration will not be covered. Any new product purchased or service performed outside of the continental United States or its possessions. Uncrating, setup, installation, or adjustments of customer operated controls. [. . . ]