User manual HITACHI 50GX30

[. . . ] PROJECTION COLOR TV 43GX10B 50GX30B OPERATING GUIDE 50DX10B 60DX10B IMPORTANT SAFETY INSTRUCTIONS 2-4 FIRST TIME USE 5-17 THE GENIUS REMOTE CONTROL ULTRATEC BIT-MAP ON-SCREEN DISPLAY 18-29 SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER 30-51 USEFUL INFORMATION INDEX 52-59 As an ENERGY STAR¤ Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR¤ guidelines for energy efficiency. IMPORTANT SAFETY INSTRUCTIONS Follow all warnings and instructions marked on this projection television. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. NOTE: ¥ There are no user serviceable parts inside the television. ¥Model and serial numbers are indicated on back side of the television. [. . . ] Press the button again to reduce the size of the subpicture. Press the PIP button the fourth time to remove the sub-picture from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by highlight). Press the INPUT button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3, VIDEO: 4 and ANTENNA sources. Main Picture ANT 10 PIP VIDEO: 1 ANT 10 PIP VIDEO: 1 ANT 10 PIP VIDEO: 1 PIP PIP PIP Sub Picture ANT 10 PIP 23 PICTURE-IN-PICTURE (PIP) SWAP button If you wish to switch what is being shown on the main picture to the Sub-Picture, press the SWAP button. ANT A 31 PIP VIDEO: 1 Gray background Green color SWAP VIDEO: 1 PIP ANT A 31 Gray background Green color MOVE button To move the sub-picture to another corner, press the MOVE button. Tthe sub-picture moves one step counterclockwise every time the MOVE button is pressed. (Example below illustrates the MOVE operation). MOVE CURSOR buttons The cursor button will move the PIP position to any of the four corners depending on which CURSOR button is pressed. The PIP will move according to the direction of the CURSOR button. 24 PICTURE-IN-PICUTRE (PIP) FREEZE button If you wish to freeze the Sub-Picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again. ANT A 31 PIP VIDEO: 1 FREEZE FREEZE Quick FREEZE button Press this button without a Sub-Picture to freeze the picture you are currently viewing. Press this button again to return to normal viewing. ANT A 31 PIP VIDEO: 1 FREEZE FREEZE CAUTION: A pattern burn may develop if the Sub-Picture is left in the same corner permanently. If the PIP feature is used frequently, occasionally shift the Sub-Picture to a different corner. You may also vary its position using the CURSOR , , , buttons. 25 USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR. Aim the remote control at the front of your VCR. Press the DVD/VCR button to switch to the VCR pre-coded mode. Hold down the DVD/VCR button on the remote, enter the two digit preset code that matches your VCR as shown on page 29. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off after five seconds, try a different two digit preset code. 4. POWER TV CBL/SAT SWAP DVD/VCR PIP HELP MOVE FREEZE VCR button This button allows the remote to control your VCR by setting it to VCR mode. PIP CH MENU EXCLUSIVE TV Buttons These buttons are for operating the TV. SELECT MUTE EXIT LAST CH VOL CH PRECODED VCR BUTTONS These buttons always transmit the chosen precoded VCR codes. 1 4 7 INPUT 2 5 8 0 3 6 9 STATUS REC TV/VCR PIX NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR s code has not been precoded into the remote. [. . . ] Press the power switch (ON/OFF switch) once. If there is still no power, wait 30 seconds and press the power switch again. If there is still no power, unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in. [. . . ]