User manual HITACHI 50UX23K

[. . . ] IMPORTANT -1- PROJECTION COLOR TV 60SX10B/11K, 50SX7P, 50UX22B/23K, 46UX20B/21K OPERATING GUIDE TABLE OF CONTENTS IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY TIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PICTURE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After replacing the batteries repeat the entire programming procedure stated above. If your VCR does not have a power function, the remote will issue the CHANNEL UP function. PRECODED VCR BUTTONS These buttons transmit the chosen precoded VCR codes. EXCLUSIVE TV BUTTONS These buttons are for operating the TV. USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the pre-coded function for your cable box This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system in your cable box. Set the MULTI-PAGE select switch to"TV/CABLE". Aim the remote control at the front of your cable box. While holding down the CABLE POWER button on the remote, enter the 2 digit preset code that matches your cable box as shown on page 26. The remote will turn off your cable box when the correct 2 digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off after 5 seconds, try another 2 digit preset code. The remote will now control your cable box. NOTES: 1. If your cable box cannot be operated after performing the above procedures, this means that your cable box codes have not been precoded into the remote. In the unlikely event that your cable box cannot operate after performing the above procedures, consult your cable box operating guide. The remote control will remember the codes you have programmed in until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure stated above. If your cable box does not have a power function, the remote will issue the CHANNEL USING THE REMOTE TO CONTROL AUDIO EQUIPMENT FUNCTIONS UP function. - 27 - PRECODED FOR CABLE BOX These buttons transmit the chosen precoded CATV codes. EXCLUSIVE TV BUTTONS These buttons are for operating the TV. USING THE REMOTE TO CONTROL AUDIO EQUIPMENT FUNCTIONS Operating the pre-coded function for your audio equipment This remote is designed to operate different types of audio equipment. You must first program the remote to match the remote system in your audio equipment. Set the MULTI-PAGE select switch to"AUDIO". Turn ON the audio component you wish to control with your remote (AMP, CD, or TAPE). Aim the remote control at the front of your audio equipment. While holding down the button on the remote which corresponds with the component you wish to control (AMP, CD, or TAPE), enter the 2 digit preset code that matches your audio component as shown on page 26. [. . . ] Important Notice: Retain your sales receipts for warranty purposes. Please complete the section below for your records, as it may be needed in the event of loss. HITACHI WARRANTY CARD, back Projection TV Limited Warranty Registration (For your record - Attach sales receipt to this card) Model no. Dealer Name Date of Purchase Dealer Address City State Zip 1 - 56 - FYI Only!!! We have had many callers tell us the magic focus feature did not converge their sets properly. If the caller complains the Magic Focus feature is not working, follow instructions below, then see "Technical Survey" in HP02. [. . . ]