User manual HITACHI 50UX52B

[. . . ] Home Electronics Division may void the user s warranty. POWER SOURCE This projection television is designed to operate on 120 volts 60Hz, AC current. Insert power cord into a 120 volt 60Hz outlet. TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE. NOTE: This television receiver will display television closed captioning, ( paragraph 15. 119 of the FCC rules. CC or ), in accordance with CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other hazards. [. . . ] Press the button again to reduce the size of the subpicture. Press the PIP button a third time to remove the sub-picture from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by highlight). Press the INPUT button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, and ANTENNA source. Main Picture ANT 10 PIP VIDEO: 1 ANT 10 PIP VIDEO: 1 ANT 10 PIP PIP PIP Sub Picture NOTE: When the COMPONENT VIDEO: Y-CBCR INPUT 2 is selected as PIP, it will appear as a blank sub-picture. 22 PICTURE-IN-PICTURE (PIP) PICTURE-IN-PICTURE CONT. SWAP button If you wish to switch what is being shown on the main picture to the sub-picture, press the SWAP button. ANT 10 VIDEO: 1 VIDEO: 1 ANT 10 SWAP MOVE button To move the sub-picture to another corner, press the MOVE button. The sub-picture moves one step counterclockwise every time the MOVE button is pressed. (Example below illustrates the MOVE operation for initial shipping conditions. If you have customized a PIP position, the MOVE operation may differ slightly from this example. ) ANT 10 VIDEO: 1 MOVE ANT 10 VIDEO: 1 MOVE ANT 10 VIDEO: 1 MOVE ANT 10 VIDEO: 1 23 PICTURE-IN-PICTURE (PIP) FREEZE (FRZ) button (With PIP ON) If you wish to freeze the sub-picture, press the FRZ button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FRZ button again. FREEZE (FRZ) button with PIP OFF (Quick Freeze) Press the FRZ button without a sub-picture to freeze the picture you are currently viewing. The MENU button will act as the VCR MENU button for HITACHI VCRs. The LST-CH button will act as your VCR ENTER button if required. The SLEEP button will act as your VCR 100 button if required. 5. * POWER TV HELP PIP CABLE PIP CH SWAP MOVE VCR TV/VCR FRZ REC STOP PAUSE MENU VOL EXIT RECALL LST-CH CH MUTE LIGHT 1 VCR Button This button allows the remote to control your VCR by setting it to VCR mode. PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program. EXCLUSIVE TV Buttons These buttons are for operating the TV. 2 5 8 0 3 6 9 SLEEP 4 7 INPUT CLU-436UI NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 25 USING THE REMOTE TO CONTROL CABLE BOX/SATELLITE FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system in your cable box. Aim the remote control at the front of your cable box. Press the CABLE button on the remote to switch to cable mode. [. . . ] Excessive heat or moisture may cause the unit to cease operation. When the batteries run down, remote control operation will become erratic or possibly stop altogether. Replace the old batteries with two new AA size batteries. Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp, resulting in a distorted picture. 54 RECEPTION PROBLEMS ¥ IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. ¥ GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. [. . . ]