User manual HITACHI 50V710

[. . . ] LCD REAR PROJECTION TELEVISION Operating Guide for 42V710, 50V710, 60V710 42V715, 50V715, 60V715 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-40 ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP). INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices. PRECODED AUDIO Buttons These buttons transmit the chosen precoded Audio component codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. GUIDE C. C. MY AUDIO EQUIPMENT CODE IS: CD AMP/RCVR NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes. Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment. 37 USING YOUR REMOTE "ENT" BUTTON TO ACCESS THE SPECIFIED INPUT OF THE TV INPUT ACCESS This optional feature allows the user of the remote control to setup it's ENTER (ENT) button to access the specified input of the TV. Setup for this feature is applicable to the remote control's normal mode only and only applies to the DVD, CBL, STB, PVR and AMP modes. Select the desired device mode (DVD, CBL, STB, PVR, or AMP) by using your SOURCE ACCESS buttons ( , LED indicator to the corresponding selection. Hold down the ENTER (ENT) button on the remote and enter the four digit preset code that matches your device as shown on pages 39-40. Then enter the assigned input number (1-5) that the device is related to. If done correctly, the device LED indicator will flash 3 times to confirm proper setup. The remote will now control the desired device. ) to position the THE REMOTE CONTROL 7. Pressing the ENTER (ENT) button will now access the video input (1-5) of the desired device. SETUP EXAMPLE (Hitachi DVD with precode 0573 connected to INPUT 1 of the TV) Select DVD mode by using your SOURCE ACCESS buttons ( , the LED indicator to DVD. ) to position , , , , Hold down the ENTER (ENT) button and press the numbers 0, 5, 7 and 3. Then press the number 1 for the assigned input number of the DVD player. GUIDE Release ENTER (ENT) button. If done corrrectly, the device LED indicator will flash 3 times to confirm proper setup. C. C. The remote will now control the DVD player. Press the ENTER (ENT) button to instantly access the video input of your DVD on Input 1. NOTES: 1. Assigned input numbers can be used more than once if applicable. 38 PVR/VCR, CABLE, SATELLITE, DVD AND AUDIO CODES FOR REMOTE CONTROL VCR BRAND . [. . . ] You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused or encouraged by your failure to abide by the terms of this License Agreement. You agree to defend, indemnify and hold HAL-HED and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this License Agreement and/or any use by you of the Software in combination with third party software. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, animation, video, audio, music, text, and "applets" incorporated into the Software), and any accompanying printed materials are owned by HAL-HED. All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. [. . . ]