User manual HITACHI 53SDX89B

[. . . ] Home Electronics Division may void the user s authority to operate the equipment. POWER SOURCE This projection television is designed to operate on 120 volts 60Hz, AC current. Insert power cord into a 120 volt 60Hz outlet. TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE. NOTE: This television receiver will display television closed captioning, ( paragraph 15. 119 of the FCC rules. CC or ), in accordance with CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other hazards. [. . . ] The remote will now control your VCR. POWER 5. NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR s code has not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. If your VCR does not have a power function, the remote will issue the CHANNEL UP function. The MENU button will act as the VCR MENU button for HITACHI VCRs. REC STOP PAUSE 3. SLOW PROG TV/VCR TV/CABLE/SAT VCR LST-CH AUDIO 4. VOL MUTE CH 5. INFO EXIT 6. The LST-CH button will act as your VCR ENTER button if required. The SLEEP button will act as your VCR 100 button if required. The REC button must be pressed two times to begin VCR recording. This button will also act as the VCR record button when the remote is in CABLE or SAT mode. RECALL FAV CH GUIDE L I G H C. S. T 7. MENU FAV CH 8. SVCS REC SCHED SELECT 1 4 PRECODED VCR buttons These buttons transmit the chosen precoded VCR codes. This remote is designed to operate certain types of audio equipment. You must first program the remote to match the remote system of your audio equipment. Set the MULTI-PAGE select switch to AUDIO. Turn ON the audio component you wish to control with your remote control (AMP, CD, or TAPE). Aim the remote control at the front of your audio equipment. Hold down the button on the remote which corresponds with the component you wish to control (AMP, CD, or TAPE), enter the two digit preset code that matches your audio component as shown on page 33. The remote will turn off your audio component when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your audio component. If the audio component does not turn off after five seconds, try a different two digit preset code. The remote will now control your audio component. POWER 5. 6. Repeat steps 2-5 until all audio equipment preset codes are programmed into the remote. AMP CD TAPE NOTES: 1. [. . . ] Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. ¥ SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. ¥ RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from the TV set to a considerable distance. 66 USEFUL INFO SYMPTOMS No Picture, no sound © Sound OK, picture poor © Picture OK, sound poor © Picture blurred © Lines or streaks in picture Poor reception on some channels Picture rolls vertically No color © Poor color © ©© HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1. [. . . ]