User manual HITACHI 55HDT51

[. . . ] PLASMA TELEVISION AVC (Audio Video Control Center) & Plasma Display Monitor Operating Guide for 42HDT51, 55HDT51 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-49 ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You must first program the remote to match the remote system of your DVD player (refer to pages 48-49 for pre-codes). Aim the remote control at the front of your DVD player. To switch to DVD pre-coded mode, use the SOURCE ACCESS buttons ( the corresponding selection. , ) on the remote control to position the LED light to 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your DVD player, as shown on pages 48-49. The indicator light will flash 3 times if the code was accepted. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different four digit preset code. The remote will now control your DVD player. You will need to set the display type of your DVD player to 16:9 widescreen. 5. 6. THE REMOTE CONTROL 7. NOTES: 1. If your DVD player cannot be operated after performing the above procedures, your DVD player's code has not been precoded into the remote. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. GUIDE A/V NET PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. MY DVD PLAYER CODE IS: NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player. 44 HOW TO USE THE REMOTE TO CONTROL VCR/PVR FUNCTIONS Operating the precoded function for your VCR/PVR (Personal Video Recorder). This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to pages 48-49 for pre-codes). Aim the remote control at the front of your VCR/PVR. To switch to VCR/PVR pre-coded mode, use the SOURCE ACCESS buttons ( to the corresponding selection. , ) on the remote control to position the LED light 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your VCR/PVR, as shown on pages 4849. The indicator light will flash 3 times if the code was accepted. [. . . ] You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused or encouraged by your failure to abide by the terms of this License Agreement. You agree to defend, indemnify and hold HAL-HED and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this License Agreement and/or any use by you of the Software in combination with third party software. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, animation, video, audio, music, text, and "applets" incorporated into the Software), and any accompanying printed materials are owned by HAL-HED. All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. [. . . ]