User manual HITACHI 57S500

[. . . ] PROJECTION COLOR TV 51S500 57S500 65S500 OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-18 THE REMOTE CONTROL 19-36 Video Audio Aspect Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 37-63 Sel USEFUL INFORMATION INDEX 64-70 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. [. . . ] The indicator light will flash 3 times if the code was accepted. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your settop-box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code. The remote will now control your set-top-box/satellite receiver. POWER VCR CBL STB SOURCE WIZARD CD DVD PVR AMP 5. 6. THE REMOTE CONTROL NOTES: 1. If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-topbox/satellite receiver code has not been precoded into the remote. In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. The ANT button will act as the TV/STB button when in STB mode. SET-TOP-BOX (STB) button This button allows the remote to control your satellite receiver by setting it to SET-TOP-BOX/SATELLITE mode. PRECODED SET-TOP-BOX/SATELLITE RECEIVER buttons These buttons transmit the chosen precoded set-topbox/satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. TV 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT C. C. PHOTO ASPECT VIRTU AL H D 3. ME NU EX IT VOL SELECT CH MUT E CH LAST VID 5 4. VID 1 VID 2 VID 3 VID 4 PIP SURF FREEZE PIP MODE PIP ACCESS SWAP DAY/NIGHT REC MY SATELLITE RECEIVER/STB CODE IS: NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-topbox/satellite receiver. 32 USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to page 36 for pre-codes). Aim the remote control at the front of your DVD player. Press and release the DVD button to switch to DVD pre-coded mode. Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 36. The indicator light will flash 3 times if the code was accepted. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct two digit preset code is entered. [. . . ] BBE, and BBE symbol are registered trademarks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc. Dimensions: 51S500 · · · · Height (in. ) (mm) Width (in. ) (mm) Depth (in. ) (mm) Weight (lbs. ) 50 1/4 1, 275. 0 48 3/4 1, 239. 0 25 1/16 636. 0 238 Inputs: · · · · · Power Input . . 1. 3W Power Consumption - Refer to rear panel at the back of the T. V. [. . . ]