User manual HITACHI 61SBX59B

[. . . ] PROJECTION COLOR TV 61SBX59B OPERATING GUIDE 53SBX59B IMPORTANT SAFEGUARDS 2-4 FIRST TIME USE 5-21 THE GENIUS REMOTE CONTROL 22-33 SET UP CUSTOM VIDEO AUDIO THEATER INFO ULTRATEC BIT-MAP ON-SCREEN DISPLAY 34-64 USEFUL INFORMATION INDEX 65-69 IMPORTANT Follow all warnings and instructions marked on this projection television. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PROJECTION TELEVISION TO RAIN OR MOISTURE. NOTE: ¥ There are no user serviceable parts inside the television. ¥Model and serial numbers are indicated on back side of the television. ¥ This television is not intended for use in a computer room. CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user s authority to operate the TV. MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. [. . . ] Press the CABLE button on the remote to switch to CABLE mode, or the SAT button to switch to SAT mode. Aim the remote control at the front of your cable/satellite box. Hold down the CABLE/SAT button on the remote, enter the two digit preset code that matches your cable/satellite box as shown on page 33. The remote will turn off your cable/satellite box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable/satellite box. If the cable/satellite box does not turn off after five seconds, try another two digit preset code. The remote will now control your cable/satellite box. 6. , POWER NOTES: 1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box code has not been precoded into the remote. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures, please consult your cable/satellite box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. If your cable/satellite box does not have a power function, the remote will issue the CHANNEL UP function. The LST-CH button will act as the cable box ENTER button if required. The SLEEP button will act as your cable box 100 button if required. The INPUT button will act as the TV/SAT button when in SAT mode. TV CABLE SAT PIP SWAP MOVIE PIP CH HELP FRZ TV/CABLE/SAT VCR 3. LST-CH AUDIO 4. VOL MUTE CH , 5. INFO EXIT GUIDE L I G H C. S. T 6. RECALL FAV CH MENU FAV CH 7. SVCS REC SCHED SELECT 1 PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. PRECODED SATELLITE BOX buttons These buttons transmit the chosen precoded satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. 2 5 8 0 3 6 9 SLEEP , 4 7 INPUT CLU-615MP 31 USING THE REMOTE TO CONTROL AUDIO EQUIPMENT FUNCTIONS Operating the precoded function for your audio equipment. This remote is designed to operate certain types of audio equipment. You must first program the remote to match the remote system of your audio equipment. Set the MULTI-PAGE select switch to AUDIO. Turn ON the audio component you wish to control with your remote control (AMP, CD, or TAPE). [. . . ] Press the power switch (ON/OFF switch) once. If there is still no power, wait 30 seconds and press the power switch again. If there is still no power, unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in. [. . . ]