User manual HITACHI 61SWX01W

[. . . ] PROJECTION COLOR TV 53SWX01W OPERATING GUIDE 61SWX01W IMPORTANT SAFEGUARDS 2-4 FIRST TIME USE 5-24 THE GENIUS REMOTE CONTROL 25-37 SETUP CUSTOMIZE VIDEO AUDIO THEATER ULTRATEC BIT-MAP ON-SCREEN DISPLAY 38-68 USEFUL INFORMATION INDEX 69-72 IMPORTANT Follow all warnings and instructions marked on this projection television. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PROJECTION TELEVISION TO RAIN OR MOISTURE. NOTE: ¥ There are no user serviceable parts inside the television. ¥Model and serial numbers are indicated on back side of the television. ¥ This television is not intended for use in a computer room. CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user s warranty. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. [. . . ] Aim the remote at the satellite receiver and press the POWER button. The remote will turn off your satellite receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your satellite receiver. If the satellite receiver does not turn off, try a different two digit preset code. The remote will now control your satellite receiver. TV POWER 5. 6. NOTES: 1. If your satellite receiver cannot be operated after performing the above procedures, your satellite receiver code has not been precoded into the remote. In the unlikely event that your satellite receiver cannot be operated after performing the above procedures, please consult your satellite receiver operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. The INPUT button will act as the TV/SAT button when in SAT mode. VCR CBL SAT SOURCE WIZARD DVD AV1 AV2 AV3 1 4 7 2 5 8 0 3 6 9 SLEEP LAST CH INPUT TV/PC HELP ASPECT C. S. 3. ME NU EX IT VOL SELECT CH 4. SV CS MUT VCR PLUS + E INFO RECA LL SC HD TV GUIDE/ PIP PIP CH FREEZE SATELLITE (SAT) button This button allows the remote to control your satellite receiver by setting it to SATELLITE mode. PRECODED SATELLITE RECEIVER buttons These buttons transmit the chosen precoded satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. PIP MODE PIP ACCESS SWAP PROG TV/VCR SLOW REC MY SATELLITE RECEIVER CODE IS: NOTE: Refer to instruction manual of the Satellite Receiver for operation of the buttons exclusively for the Satellite Receiver. 34 USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player. Aim the remote control at the front of your DVD player. Press and release the DVD button to switch to DVD pre-coded mode. Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 37. The indicator light will flash 3 times if the code was accepted. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code. [. . . ] IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1. Press the power switch (ON/OFF switch) once. If there is still no power, wait 30 seconds and press the power switch again. If there is still no power, unplug the power cord from the wall. [. . . ]