User manual HITACHI 65S700

[. . . ] PROJECTION COLOR TV 51S700 57S700 65S700 OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-20 THE REMOTE CONTROL 21-40 Video Audio Chan. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 41-72 Sel USEFUL INFORMATION INDEX 73-79 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. [. . . ] After replacing the batteries repeat the entire programming procedure as stated above. The ANT button will act as the TV/STB button when in STB mode. SET-TOP-BOX (STB) button This button allows the remote to control your satellite receiver by setting it to SET-TOP-BOX/SATELLITE mode. PRE-CODED SET-TOP-BOX/SATELLITE RECEIVER buttons These buttons transmit the chosen pre-coded set-topbox/satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. TV 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT A/V NE T GUIDE ASPECT VIRTU AL H D 3. ME NU EX IT VOL SELECT CH MUT E CH LAST VID 5 4. VID 1 VID 2 VID 3 VID 4 PIP SURF FREEZE PIP MODE PIP ACCESS SWAP DAY/NIGHT REC MY SATELLITE RECEIVER/STB CODE IS: NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-topbox/satellite receiver. 36 USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to page 40 for pre-codes). Aim the remote control at the front of your DVD player. Press and release the DVD button to switch to DVD pre-coded mode. Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 40. The indicator light will flash 3 times if the code was accepted. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code. The remote will now control your DVD player. 5. 6. 7. THE REMOTE CONTROL You will need to set the display type of your DVD player to 16:9 widescreen. POWER NOTES: 1. If your DVD player cannot be operated after performing the above procedures, your DVD player's code has not been precoded into the remote. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. TV VCR CBL STB SOURCE WIZARD CD DVD PVR AMP 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT A/V NE T GUIDE ASPECT V IRTU AL H D ME NU EX IT VOL SELECT CH DVD Button This button allows the remote to control your DVD player by setting it to DVD mode. VID 1 MUT E CH LAST VID 5 PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. VID 2 VID 3 VID 4 PIP SURF FREEZE PIP MODE PIP ACCESS SWAP DAY/NIGHT REC MY DVD PLAYER CODE IS: NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player. 37 USING YOUR REMOTE TO CONTROL PVR FUNCTIONS Operating the precoded function for your PVR (Personal Video Recorder). [. . . ] *Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. . 470mVrms, 1k Ohm · Power Consumption · S-Video - Refer to rear panel at the back of the T. V. . 1. 0Vp-p, 75 Ohm · Antenna input impedance . [. . . ]