User manual HITACHI CDR-8430 32X

[. . . ] 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For Germany / Für Deutschland Module dürfen nur an eine Sicherheits-Kleinspannungs-Versorgung(SELVKreise) nach EN609501/VDE 0805 angeschlossen werden. Die Trennung von Netzspannung muß durch einen Sicherheitstransformator geschehen. 32x CD-ROM Manual - Page 3 Labeling The equipment is classified as a Class 1 level Laser product. This label is fixed to the bottom of the CDROM Drive. Important Safeguards SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT 1. [. . . ] It may damage or discolor the coating of the CD-ROM Drive or damage or deform discs. · Clean your CD-ROM Drive including the Disc Tray and discs with a clean, dry, soft cloth at least once a month. · Cleaning needed warning If you begin to get error messsages that your drive is unable to read a disc, it may mean that cleaning is needed. · Eject the disc and visually inspect the disc for scratches. If there are scratches on the surface of the disc change the disc. · Eject the disc and clean as follows. Clean the disc with a clean, dry, soft cloth. Clean your CD-ROM drive's pick-up lens using a cleaning disc. 32x CD-ROM Manual - Page 7 Controls and Functions 2 6 Front Panel Rear Panel 34 1 5 78 9 10 1) LOADING/UNLOADING/BUSY INDICATOR Indicator blinks green only when the Disc Tray is being opened or closed, or when the CD-ROM drive is accessing data. 2) DISC TRAY When the power of the CD-ROM Drive is turned off, the Disc Tray cannot be opened and closed. 3) HEADPHONE JACK ( 3. 5 mm) 4) HEADPHONE VOLUME CONTROL Adjust the headphone volume. 5) OPEN/CLOSE BUTTON Press this button to open or close the Disc Tray. 6) MANUAL EMERGENCY EJECT HOLE Only in case of emergency. If the Disc Tray does not open when the OPEN/CLOSE Button is pressed, the CD-ROM Drive's Manual Emergency Eject mechanism may be activated. This should be used only in case of an emergency. (See page 12 about Manual Emergency Eject Procedure) 7) AUDIO OUTPUT TERMINAL Circuit Board Rch GND Lch 32x CD-ROM Manual - Page 8 8) DEVICE CONFIGURATION JUMPER This Connector is used to set operation modes such as Master, Slave and CSEL 642 Device is Master 531 or (default setting) Device is Slave Cable Select 9) ATAPI INTERFACE CONNECTOR ATAPI bus connection (40 pin) 10) POWER SUPPLY CONNECTOR (DC Input) For connecting the power supply cable. Circuit Board +5V GND +12V Installation Requirements HARDWARE · · · · · CD-ROM Drive Interface card Interface cable Power supply cable Mounting screws 32x CD-ROM Manual - Page 9 HARDWARE OPTION · Audio connecting cable · Sound Card SOFTWARE · CD-ROM device driver NOTE: If you need a interface card or interface cable or CD-ROM device driver, contact your dealer. Hardware Installation To install this CD-ROM drive in the host computer, refer to the instruction manual of each host computer. And to install the interface card in the host computer, refer to the instruction manual of each host computer and each interface card. Install the CD-ROM Drive following general installation procedure shown below. 1) Check the Device Configuration Jumper settings of the CD-ROM Drive such as Master, Slave, CSEL. (See page 9) 2) Turn off the host computer and unplug the power supply cable of the host computer. 4) Install the CD-ROM Drive into the host computer and mount tightly by screws. 5) Check the settings of the interface card. 6) Install the interface card in the slot. [. . . ] Pull the Disc Tray. Lens Cleaning A commercially available "Laser Lens Cleaning Disc" may be used to clean up the pick-up lens of the CD-ROM Drive. Use the Compact Disc Laser Lens Cleaner LLC-1. (by AUDIO SOURCE in U. S. A. , by AKUSTIK SISTEME VERTRIEBS GHBH in GERMANY and by SAEC COMMERCE CO. , LTD. 2) Using the small brush supplied with the cleaning disc case, straighten up the disc cleaning brushes on the back of the cleaning disc. [. . . ]