User manual HITACHI CM1711MET

[. . . ] Apple and Macintosh are registered trademarks of Apple Computer, Inc. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. Energy Star is a trademark of Environmental Protection Agency. -ENG The provided USH by flat screen CRT with anti-glare, dynamic focus circuit, dark glass, and an INVAR shadow mask gives the sharpest focus and highest contrast to minimize eye fatigue. Sharpest Focus and Highest Contrast Wide-range Multi-Scanning Automatic scanning and automatic adjustment to conform with a wide range of scanning frequencies and user requirements. Digital Picture Control Function Position, size, pincushion, trapezoid and rotation are adjustable by digital controls. Geometry setting can be stored for different H/V frequencies. [. . . ] n Use only the correct voltage power outlet with safety ground connection. (This monitor automatically adjust to the input voltage 100 - 120 / 200 - 240V. ) n The receptacle should be close to the monitor and easily accessible. 5 A FOR THE CUSTOMERS IN U. K. =ENG - USH THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is , xtuired, ensure it is of the same oolour as that visible on the pin face of the plug. Fuse oovers are available from your dealer. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too shot-l to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician. If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible shook hazard by inadvertent connection to the mains supply. WARNING: THIS EQUIPMENT MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and Yellow = Earth, Blue = Neutral, Brown = Live. Green &Yellow to Earth Brown to Live Fuse Blue to Neutral Cord Clamp As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol @ or coloured GREEN or GREEN and YELLOW. The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. 6 3. Signal Input Connection Connect the Signal Input Connector to the D-Sub Mini IBpin signal output terminal of the host computer. to the host computer b' QIg , REAR VIEW ENGe LISH - +@- Signal Input Connector l If the graphics board supplies more than one type of sync. signal type will be automatically selected by the monitor, with the priority shown in the following table. 4. Power On Turn on the Power Switch of the monitor first, then the computer. Refer to Page 9 `POWER ON/OFF". NOTICE w After turning OFF the switch, wait at least 5 seconds to restart the monitor. Otherwise the monitor may operate unusually. n If the picture doesn't appear, turn OFF the power switch, make sure of'the following and wait at least 30 seconds to restart the monitor. Make sure the power switch of the computer, power cord connection, signal cable connection and the input sync. 1 If the colour is impure on the screen after turning ON the monitor, wait for about 10 minutes and press the Degauss button. 7 l Microprocessor-based preset functions can store 20 sets of geometry settings including the standard settings. The following industrial standard settings have been preprogrammed by the factory. NOTE w Input signals with approximately the same frequencies may be regarded as the same signal. [. . . ] The muting period depends on the time that takes until the replaced signal becomes stable. 13 Et;f l This monitor complies with VESA, Nutek, and Energy Star power saving requirements. The power saving system works only when used with VESA DPMS compliant PC's and/or graphic controllers. e This monitor complies with VESA DDC1/2B specifications. Plug & Play is a system with computer, peripherals (including monitors), and operating system. It works when the monitor is connected to DDC ready computer that is running an operating system software that is capable for the plug & play. CRT 17 inches picture tube, Anti-Reflection coat, 0. 22 mm (optional 0. 24 mm) horizontal dot pitch, lnvar shadow mask, Black matrix, Short persistence phosphors. [. . . ]