User manual HITACHI CM620ET

[. . . ] CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. lNSTALWTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5m 5. USE OF TILT. SWIVEL CONTROLS POWER PLUG& . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lO AND ADJUSTMENTS SYSTEM MANAGEMENT PWY . . . . . . . . . . . . . . . . . . . . . . [. . . ] (This monitor automatically adjust to the input voltage 100- 120/ 200- 240V. ) 2 s CAUTION for 200V operation only This equipmentrelies on the protective devices in the building installation for short-circuit and overcurrent protection. Refer to the following table for the suitable number and location of the protective devices which should be provided in the building installation. Protective devices in single - phase equipment or sub - assemblies Protection against Equipment to be connected to POWER SYSTEMS with earthed neutral reliably identified Equipment to be connected to any supply, including IT POWER SYSTEMS and supplies with reversible plugs Earth faults Over-current Earth faults Over-current Minimum number of fuses or circuit breaker poles 1 1 2 1 Location w m w i Both conductors Either of the two conductors Both conductors Either of the two conductors Verify that the protective devices in the building installation meet the conditions in the table prior to installing the equipment. s BE CAREFUL OF POWER CORD CONNECTION ! Check that the connecting portions of power cord is clean, and connect them firmly. THE POWER CORD FOR COMPLETE SEPARATION !W REMOVE For complete separation from the power source, remove the power cord from the monitor or from the wall outlet. s AVOID FREQUENT POWER ON-OFF SW!TCHING ! DO NOT repeat OFF and ON in a short period. It may cause blurred colors or distortion of the displayed pattern. s BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power. s ABOUT CLEANING This monitor has a non-glare and anti-electrostatic treatment on the surface of the screen. Use water or alcoholic solvent with soft cloth like gauze to clean the surface of the screen. NEVER use abrasive, glass cleaner containing highly concentrated ammonia and strong base chemicals since they damage the surface treatment. Clean the cabinet and controls with a lightly moistened soft cloth. DO NOT use aerosol sprays, solvents or abrasive cleaners. 3 s FOR THE CUSTOMERS -- IN THE U. K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINIAND EUROPE. PLEASE REFER TO THE NOTES ON THIS PAGE. iMPORTANT WORDING FOR CLASS I FOR UNITEDKINGDOM INSTRUCTION BOOKS AND LABELS EQUIPMENT The mains lead on this equipment value of which is indicated on the an ASTA or BSI approved BS 1362 detachable never use the plug with ensure it is of the same colour as available from your dealer. is supplied with a moulded plug incorporating a fuse, the pin face of the plug. Should the fuse need to be replaced, fuse must be used of the same rating. If a replacement fuse cover is required, that visible on the pin face of the plug. Fuse covers are If the plug fitted is not suitable for the DO NOT cut off the mains plug from this equipment. power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician. If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply. WARNING: THIS EQUIPMENT MUST BE EARTHED iMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and Yellow = Earth, Blue= Neutral, Brown = Live, Green & Yellow to Earth Brown to Live Fuse Blue to Neutral Cord Clamp As these colours may not correspond with the coloured markings identi~lng the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol @ or coloured GREEN or GREEN and YELLOW. The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. 4 Before installation, please check the contents of the shlpplng carton. The carton should contain the following Itf'nls Colour monitor Power cord User manual Adapter for Apple Mac 11 (option) [f any of the above item are missing, contact your supplier as soon as possible. 4. INSTALLATION Before connecting, make sure that the line voltage is exactly within voltage range shown on the label located on the rear cover. If you are uncertain of the type of line voltage where this monitor will be used, consult your local power company or appliance dealer. c, Make sure the monitor and the computer are turned off before operation. Plug the other end of the power cord into a power outlet. [. . . ] on Green: 0. 3VP-P (for CM630ET only) : 31-69 kHz for CM620ET Horizontal 31-86 kHz for CM630ET : 47-130Hz Vetiical Video Response Power 110 MHz nominal 135 MHz nominal for CM620ET for CM630ET (de~ends on video card) 120 /200 -240 VAC for CM620ET 100-120 / 200-240 VAC for CM630ET 60/50 Hz, 2. 5 A max. Degaussing : line operated automatic& manual : 115 W max. for CM630ET (Provided Power Save Circuit. ) Low Radiation Plus & Plav Operating MPR- II / TCO VESA DDC `") Temperature Humidity Altitude : I12B :5 to 35 degree C : 10to 90 %R. H. :Otolooooft Weight Dimensions 17. 5 kg (38 lb) approx. [. . . ]