User manual HITACHI CM802E

[. . . ] HITACHI COLOUR 1140/V/TOR V2. J-Lw CIV1802E CM802ET CM803ET with For CM802ET and CM803ET only USER'S MANUAL EasyMenu! is HITACHI'S On Screen Display function for easy operation, EasyManu > f READ THE INSTRUCTIONS INSIDE KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. i \ CAREFULLY SERIAL No. The serial number is located on the rear of the monitor. '00%4+ P . u?A*b & ~ EPA POLLUTION PREVENTER This monitor is Energy Star compliant when used with a computer equipped with VESA DPMS. The Energy Star emblem does not represent EPA endorsement of any product or service. COLOUR MONITOR CM802E CM802ET CM803ET NOTICE USER MANUAL The information in this manual is subject to change without notice. [. . . ] (or H/V) Ground Ground Ground Ground A3 Blue Video 5 7 For models CM802E and CM802ET, use a signal cable with the D-Sub Mini 15-pin connector. = S~ell (connected to Frame Ground) D-Sub Mini 15-pin connector Terminal Pin No. 1 2 3 4 5 Signal Red Video Green Video (Sync. optional) Blue Video No Pin No connection Pin No. 6 7 8 9 10 Signal Red Ground Green Ground Blue Ground No connection Ground Pin No. 11 12 13 14 15 Signal No connection Bi-directional Data [SDA] H. Horizontal back porch should be more than 1. 2 I. JS. Horizontal blanking width should be more than 3. 5 ps. for 52 kHz -100 kHz horizontal frequency Horizontal front porch should be more than 0. 1 ps. Horizontal back porch should be more than 1. 1 I-Is. Horizontal blanking width should be more than 2. 3 IJS. s The following vertical timing conditions are recommended. Vertical front porch should be more than 9 I-IS. Vertical back porch should be more than 400 IAS. Vertical blanking width should be more than 450 I-Is. u s [f either the front or back porch is extremely long, or the data display time is extremely short, it may not be able to set the expected size and posiiton. Standard settings are subject to change without notice. s This monitor is tested and conformed compliance with ZH1/618 and EN29241 -3 (1S09241 -3) ergonomics requirement on VESA 1024 x 768- 75Hz video mode. 9 -- OPERATION a~ + ~ :, ` . . "v. +>. . , . . :, :, Z+ 1---------- *n - r 1 I I i I I /1 fl Control Panel 4 \ \ , Select Switch Adjust Switch 1 L I Page 10 "DEGAUSSING" I"'v', ''i" Page 14 "STORE" Page 10-13 "ADJUSTMENT" Page 10 "POWER ON/OFF" POWER ON/OFF q Press the Power Switch ( 0 ) , to switch the power ON/OFF. *O a E When power is ON, the power LED lights. DEGAUSSING q Press the switch ~~] , to degauss manually. the monitor is automatically degaussed during initial power on. s Use this function only when you see colour impurities on the screen after turning ON the monitor. Remember, s Wait for about 10 minutes before repeating the function. ADJUSTMENT R ~ q Press the select switch of the item you want to adjust. Then you can adjust by the SELECT shown in the following tables. [. . . ] signal which is out of set-up specification or is unstable. . . . Video Muting * When the monitor has detected the change of the signal input condition, the monitor mutes the picture automatically. This function hides scrambled images which may appear during the changing period of the input signal. The muting period depends on the time that takes until the replaced signal becomes stable. 15 - I POWER SAVING SYSTEM [ . This monitor complies with VESA, Nutek, and Energy Star power saving requirements. The power saving system works only when used with VESA DPMS compliant PC's and/or graphic controllers. I Mode Video ON Stand-by Suspend OFF Active Blanked Blanked Blanked VESA DPMS H. Sync V. Sync I Yes No Yes No Yes Yes No No Power Saving States Power LED I Power Consumption 130W (nominal) less than 30 w approx. [. . . ]