User manual HITACHI CM811ET PLUS

[. . . ] , . COLOUR MONITOR CM81 1ETPIus CM81 3ETPIUS CM81 5ETPIUS with Easy Men u ! EasyMenu USER MANUAL MANUEL lVIAhllJAL USUARIO. . . 35 D'USO. . . 5I . . . . . I BEDIENUNGSANLEITUNG. . . 19 DE MANUALE UTIL]SATEUR. . . 67 is the On Screen Display function for easy operation. 0000000 00 00 0. 0 \ READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your color monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR@ compliant when used with a computer equipped with VESA DPMS. [. . . ] Horizontal back porch should be more than 1. 2 ps. Horizontal blanking width should be more than 3. 5 ps. for 55 kHz -130 kHz horizontal frequency: Horizontal front porch should be more than 0. 1 ps. Horizontal sync, width should be within 0. 8- 3. 0 p. s. Horizontal back porch should be more than 1. 1 ps. Horizontal blanking width should be more than 2. 3 ps. s The following vertical timing conditions are recommended. Vertical Vertical Vertical Vertical front porch should be more than 9 ps. back porch should be more than 400 ps, blanking width should be more than 450 ps. s In case the front or back porch is extremely long, or the data display time is extremely short, it may not be able to set the expected size and position. s Standard settings are subject to change without notice. s This monitor is tested and conformed compliance with ZH11618 and EN29241 -3 (1S09241 3) ergonomics requirement on the following video modes : tiz", "VESA 1600x 1200-85 "VESA 1024x 768-85 t+z", "VESA 1280x 1024-85 s This monitor is tested and conformed compliance with FCC (and ICES-003) Class B requirement on the video mode "1600 x 1200- 92kHz". Hz" 8 0000000 A /, 00 00 0. 0 / ~ I I - J I \ \ -- \ -- - Control Switches Q @ @9@J9 e­e--m . "-- . . o. --$. @* @_E, , , i_e /' I @ . 2, s 00 : 1~Input Switch \ Select Switch Page 9-13 "ADJUSTMENT I Adjust Switch Page 10 "DEGAUSSING" Page 9 "POWER ONIOFF / POWER ON/OFF Press the Power switch, to switch the power ON or OFF. s When power is ON, the power LED lights. INPUT This monitor has two input terminals, INPUT 1 and INPUT 2. Therefore, you mav connect two commters simultaneouslv. When two computers are active, you' may switch the input signal by using the EasyMenu controls. INPUT SELECT INPUT 1 is the initial factory default setting. . . . . . . . . . . . . . . . . . . INPUT SELECT ~ INPUT2 INPUT1 ~ -<m> <OFF>+ ~ IN~~<~E~~~T If you would like to use INPUT 2, proceed to the "EasyMenu" and select the "INPUT SELECT mode, Press the "+" key and this will select INPUT 2. s Plug and Play function is only supported and not supported on INPUT 2. on INPUT 1, : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sample of "EasyMenu'" ;@ 60 kHti 60H, INPUT1 AUTO INPUT SELECT This monitor has an "INPUT AUTO SELECT" function which will select the input by scanning for an input signal on either INPUT 1 or INPUT 2. "ON" : press the " u " key. 9 When there is no input signal received from the input connection which was selected by "INPUT SELECT, the "INPUT AUTO SELECT" alternate connection. If there is no input signal received the monitor will default to the "POWER SAVE" mode. W If there are two computers connected to the monitor function will select the from either connection you restart and for example one of the computers or it is activated from the "POWER SAVE" mode, it is possible that the monitor may change to an undesired input connection. This may be easily correct by changing the input selection to the desired INPUT 1 or INPUT 2 using the "INPUT SELECT" function. "OFF" : Press the" s When the "INPUT H " key. AUTO SELECT" function is placed in the "OFF mode, the selected by the "INPUT automatically. 9 "' monitor will default back to the selection that has been SELECT" function, and the input will no longer be selected DEGAUSSING -- = -- Press the switch "DEGAUSS", to degauss manually. s Use this function only when you see colour impurities on the screen after turning ON the monitor. Remember, the monitor is automatically degaussed during initial power on. s Wait for about 10 minutes before repeating the function. ADJUSTMENT Press the select switch of the item you want to adjust. [. . . ] When the monitor will go into the power saving mode. (Refer to page 16) The LED of the power switch (~) flashes. [I NPUTII -- s Verify power switch of the computer and cable connection. INUfiLID SCfiN FREO When the monitor detects The EasyMenu indicates the message a sync. signal which is out "INVALID SCAN FREQ. ". of set-up specification or s Verify the specification of input signal. [. . . ]