User manual HITACHI CM814ET

[. . . ] HITACHI COLOUR MONITOR CM811 ET CM812ET CM813ET CM814ET with USER MANUAL . . . . . I BEDIENUNGSANLEITUNG. . . 19 MANUAL DE USUARIO. . . 33 MANUALE D'USO. . . 47 MANUEL UTILISATEUR. . . (3I Easy Men u ! IS HITACHI'S On Screen Display function for easy operat[on EasyMenu Oceooo 00 00 0. 0 / \ READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGYSTAR@compliant when used with a computer equipped with VESA DPMS. The ENERGY STARoemblem does not represent EPA endorsement of any product or service. [. . . ] The wire coloured BROWN must be connected to the terminal marked with the letter L or mloured BROWN or RED. 6 L INSTALLATION -- ` , taking care to maintain safety. Rear Cover Signal Input Connector \ Install the monitor in the following w / AC inlet -1 ( FRONT VIEW REAR VIEW i \ 1. Installation Install the monitor on a horizontal base. Power Cord Connection @ Make sure of using the power cord meeting the safety standard country in which you are using the monitor. @ Insert the connector of a power cord to the AC Inlet of the monitor. @ Insert the plug of the power cord to a receptacle 3. Signal Cable Connection @ Use video signal cable which is included in the carton box. (Cable model name: HD-0501 FXL) @ Insert the connector of a signal cable to the Signal Input Connector of the monitor, with attention to the suitability, and secure the screws on the connector shell firmly. @ Connect the other connector end of the signal cable to the host computer. of the AC Inlet \ A receptacle of the correct voltage \ n Signal Input Connector / g o +m \. Power Cord i I Signal Cable to the host computer 8 q Use a signal cable with the D-Sub Mini 15-pin Connector. e 5 l", , , , ", , , , Inm-mnarti~n N(. " "". , . 6 7 8 9 10 ". Red Ground Green Groul Id -, "", , Rl, ka (km Inr -, -" I [SDA] ;; 13 14 15 No connect~n Ground No connection Bi-directional Data H. (or H/V) v Sy PJcW [SCL] Datan;iock q If the graphics board supplies more than one type of sync. signal, the sync, signal type will be automatically selected by the monitor, with the priority shown in"the following table. Sync. Power On Turn on the Power Switch of the monitor first, then the computer. NOTICE : s After turning OFF the switch, wait at least 5 seconds to restart the monitor. Otherwise the monitor may operate unusually. s If the picture doesn't appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds to restart the monitor. Make sure the power switch of the computer, power cord connection, signal cable connection and the input sync. signal are right. s If the Colour is impure on the screen after turning ON the monitor, wait for about 10 minutes and press the Degauss button. STANDARD SETTINGS Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been pre-programmed by the factory. Video Mode Name ET ~ Y) 3 VESA 4 = ; 5 6 7 8 9 10 ADDle . . VESA VESA VESA VESA 1024X 1152x 768 -85 t+z 870 -75 I+z HZ 68. 68 kHz 68. 68 kHz Macintosh E`~ ~~ E 21 Color VESA 91. 15 kHz 93. 75 kHz VESA VESA VESA h L L ­ ­ -- -- ­ b ­ h ­ -- -- "~ ­ b ­ ­ b b -- "~ ­ . J ­ ­ & , 4 L 1280X 1024 -&j 1600X 1200 -75 Hz 1600X 1200. 90 1856x1392 1600x 1200-100 1600X 1200 -85 Hz 106. 25 kHz Hz 112. 50 kHz Hz 125. 00 -71 I-Iz 102. 95 kHz kHz s Input signals with approximately the same frequencies may be regarded as the same signal. The following horizontal timing conditions are recommended separate or H/V composite). for 31 kHz -55 kHz horizontal frequency: Horizontal front porch should be more than 0. 1 ps. Horizontal back porch should be more than 1. 2 ps. Horizontal blanking width should be more than 3. 5 ps. [. . . ] The horizontal frequency and vertical frequency will be indicated. s Precision frequency, Horizontal approximately Vertical approximately & 2 kHz *2Hz ~ BR IGHTNESS 5@ E4~}la S0 kllz/ 75Hz !. . . . . . . . . . . . . . Sample of "EasyMenu" \ AUTOMATIC SIGNAL CHECK the When the monitor I as detected the change of the si{ Ial input condition, monitor will indicate he condition automatically, as follc /s. Condition When the monitor detects no sync. Indication The EasyMenu indicates the message "POWER SAVE" for 5 seconds. E POUJER SfWE s Verify power switch of the computer and cable connection. F When the monitor will go into the power saving mode. [. . . ]