User manual HITACHI CMP205SXU

[. . . ] This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS. The ENERGY STAR® emblem does not represent EPA endorsement of any product or service. As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. NOTE: The information in this manual is subject to change without notice. [. . . ] : OFF 3D COMB : ON COMPONENT VIDEO SYSTEM : AREA1 SCREEN SAVER RETURN SCREEN SAVER MENU ORBITER : OFF MOVING DOTS : 2 MOVING TIMER : 10 INVERSE : OFF WHITE : OFF RETURN OFF ON Selected characters Setup hint Set to ON when high image retention potential exists such as static or still image displayed long period of time. Adjust as desired. Shift time can be set from 1 min. If 60 is selected, the set enters a power wait state 60 minutes later, with its settings canceled. When a still picture has been displayed for long before ON is selected to display the same still picture, INVERSE or WHITE helps prevent the still picture from baking into the panel. The set stops when input signal flow is interrupted. ORBITER Set to OFF. Set to ON. 1 2 3 MOVING DOTS Reduces the amount of movement. Reduces the time interval. Increases the amount of movement. Increases the time interval. MOVING TIMER INVERSE 60 OFF ON WHITE 19 ENGLISH OTHER FEATURES Automatic Store ENGLISH s Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below. Item Sound volume Sound balance Treble Bass Mute volume Input status automatic display Line correction Three-dimensional Y/C separation HD signal Language selection Contrast Brightness Color temperature Gamma correction Input signal level Color Tint Sharpness Video enhance Display area Display size Horizonal position Vertical position Dot clock frequency Dot clock phase Verical size Display VOLUME BALANCE TREBLE BASS MUTE LEVEL AUTO FREQ. 3D COMB COMPONENT LANGUAGE CONTRAST BRIGHTNESS COLOR SELECT GAMMA VIDEO LEVEL COLOR TINT SHARPNESS VIDEO ENHANCE DISPLAY AREA DISPLAY SIZE H. POSITION V. POSITION CLOCK PHASE V. SIZE Registration condition Reproduction condition One set can be recorded. During normal signal reception. One set can be recorded during common RGB1, RGB2 input; one set of two can be recorded during normal signal reception with common VIDEO 1, VIDEO 2 input. During normal signal reception. One set can be recorded During normal signal during common VIDEO 1, reception. VIDEO 2 input. One group can be recorded for each signal mode. During recording and when the same signal mode is detected. · The previously recorded items will be lost. · Text displayed across the screen appears vertically streaked, with the characters in vertical columns blurred. · Text displayed across the screen appears blurred. · A fine pattern flickers when displayed on the screen. · Adjust the dot clock frequency and phase. (Adjust the dot clock frequency first, the dot clock phase next. ) (RGB input) · Adjust the dot clock phase for the clearest viewing. (RGB input) 15 16 26 · The remote controller does not work. · Check to see if the batteries are loaded in the remote controller in opposite direction. · Check to see if the batteries in the remote controller are OK. 8 23 ENGLISH TROUBLESHOOTING (continued) Symptom Point to check · The plasma display panel is lighting the phosphors by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction. · High-precision technology is used to manufactue the plasma display panel, However in some cases, there are minor defects in some parts of the screen. Please note that this is not a malfunction. ENGLISH See page · The temperature of the display panel surface is high. - · There are locations on the screen that are different from the periphery (*). *Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc. - · Vertical stripes appear, depending on the · The plasma display panel is lighting the screen contents. [. . . ] 6) Appuyez sur la touche MENU pour ouvrir le menu MENU PRINCIPAL. 7) Appuyez plusieurs fois sur la touche SELECT pour choisir AFFICHAGE. 8) Appuyez sur pour ouvrir le menu MENU ECRAN. 9) Appuyez sur pour choisir MANUEL AJUSTE. [. . . ]