User manual HITACHI CMP401XU

[. . . ] HITACHI cannot assume liabilities for damage caused by mistake in installation or mounting, misuse, modification or a natural disaster. Note for Dealers: After installation, be sure to deliver this manual to the customer and explain to the customer how to handle the product. ENGLISH IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI PLASMA MONITOR Our reputation has been built on the quality, performance, and ease of service of HITACHI Plasma monitor. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI Plasma monitor. [. . . ] The number will be incremented (2 6 7 1 2) when this button pressed continuously. The remote control ID no. can be checked by pressing the ID SET button while holding down the ID button. ID Number Monitor [1] R/C [1] Contrast Next / Prev + 31 Adjust Return · Press the RETURN button to return to the previous screen. · If there is no operation for a period of one minute, the Adjustment Menu screen will be closed automatically. Monitor ID no. Remote control ID no. The ID remote control is operated by pressing the various buttons while holding down the ID button; Operation is possible only when the remote control and monitor ID nos. are the same. · The remote control can be operated normally by pressing the various remote control buttons without holding down the ID button. · Set the monitor using the ID No. of Function MENU. OPERATING INSTRUCTIONS (continued) PICTURE MENU MENU Picture Audio Timer Function Setup Language Select OK Set OK Picture Contrast Brightness Color Tint Picture Enhancement Color Temperature Color Temp. Adjust Reset Select OK Set : : : : : : + 31 ­ 31 0 + 31 Off Normal Reset Return OK Contrast Next / Prev + 31 Adjust Return Picture Contrast Brightness Color Tint Picture Enhancement Color Temperature Color Temp. Adjust Reset Select OK Set : : : : : : + 31 ­ 31 0 + 31 Off Normal Reset Return OK Color Temperature Next/Prev Select Normal Return Picture Contrast Brightness Color Tint Picture Enhancement Color Temperature Color Temp. Adjust Reset OK Set Select : : : : : : + 31 ­ 31 0 + 31 Off Normal Reset Return OK Picture Color Temp. Adjust Amplitude Red ­ 63 Green 0 Blue ­ 31 Cut Off Red + 31 Green 0 Blue + 31 Reset Select On/Off On Reset Return Selected characters Setup hint Adjust for maximum visibility to suit the ambient brightness. This can adjust further till [+40] by pressing and holding cursor button at [+31]. The color for [+32] to [+40] numbers will change from white to magenta. This special mode is better for dark scenes. For brighter scene some parts of the picture might not be clear. This features the spacious sound effects of a stadium. This will automatically adjust volume so each channel and input has the same average volume level. The original factory settings for the items of this Menu page can be restored by pressing the OK button. Audio Mode Movie Music Speech Favorite Treble Bass Balance Suppresses treble. Suppresses right-side sound. Enhances treble. Suppresses left-side sound. SRS TruBass Matrix Surround Perfect Volume Reset Off Low Middle High Off Off (off the function) On On (waiting to reset) TIMER MENU Picture Audio Timer Function Setup Language Select OK Set Timer Off Timer On Timer Select : 30Min. : --:-Return OK MENU Adjust Selected characters Setup hint Off Timer --Min. 90Min. --(:--) hours (- - : )- minutes This function automatically sets the power to standby status when the indicated time period has elapsed. This automatically sets the power from standby to ON when the indicated time period has elapsed. Input the required time by SELECT buttons on the remote control. On Timer OPERATING INSTRUCTIONS (continued) FUNCTION MENU Picture Audio Timer Function Setup Language Select OK Set Function Screen Saver Screen Wipe Black Side Panel Video Power Save Freeze Mode Default Zoom Reset Select Set Off On 60Min. Off Off Split Panoramic Reset Return OK MENU Function Panel Life Mode Display ID Number Inverse Standby White Gamma Reset Select Set Normal Off 1 On 60Min. Off 2. 2 Reset Return Selected characters Setup hint Screen Saver Off 60Min. 5Min. [. . . ] · If the signal from the equipment that is connected to AV4 Scart input terminal is S. Video or Composite, set this to correspond to that signal. · If the signal is RGB, it will be automatically recognized and this setting will have no effect. (Same to AV1) AV1 Auto HDTV SDTV/DVD AV2 (1st step) AV2 (2nd step) RGB Auto Composite/Component HDTV SDTV/DVD AV4 S. Video Composite OPERATING INSTRUCTIONS (continued) SETUP MENU (continued) Selected characters Setup hint Audio Input AV1 AV2 AV3 AV4 Scart Output RGB1 RGB2 (1st step) DVI-PC RGB DVI-STB Component Not Available (grayed out) This should correspond to the signal mode of the signal from the equipment that is connected to RGB1 DVI terminal. This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal. [. . . ]