User manual HITACHI CMP402HDE

[. . . ] Color Plasma Display Monitor CMP402HDE USER MANUAL BEDIENUNGSANLEITUNG MANUEL UTILISATEUR MANUAL DE USUARIO MANUALE D'USO with EasyMenu!EasyMenu is HITACHI's On Screen Display function for easy operation. (The stand is an option. ) (Le socle est en option. ) (Der Stander ist Sonderzubehor. ) (Il supporto di appoggio è un accessorio opzionale. ) (El soporte es opcional) READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. [. . . ] Ask your dealer to provide the name of a qualified installer. Consult your dealer before attempting to install this projector on the desk-top stand. In order to prevent an internal temperature increase, maintain a space of 10cm or more between the sides and other objects such as walls, etc. , so that the ventilation holes are not blocked. * CAUTION Anti-tumble measures CAUTION Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury. Securing to a wall or post After positioning, pass the hooks included with the Desk-top Stand through the holes located on both ends (left and right) at the top and fasten with M4 screws, as shown in the diagram. Using a commercially available cord, chain and clamp, secure the set to a firm wall or post. 10cm or more* Clamp Cord or chain Securing desktop Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand as shown. Using commercially available wood screws, secure the set firmly in position. yyyyyyy ;;;;;;; yyyyyyy ;;;;;;; Wood screw Two places INSTALLATION INSTRUCTIONS (continued) Component Names Front ENGLISH The Adjustment button is located on the bottom. Panel Cabinet (front frame) Remote-control sensor Stand Control panel Indicating lamp Main power switch Subpower button VOLUME button MENU button RGB button External device connection terminals External speaker terminals RGB input terminals Remote controller POWER button POWER RECALL RGB/ VIDEO RGB/VIDEO button(*) *: "VIDEO" is not available. RECALL button MUTE button MUTE VOLUME VOLUME button MENU MENU button SELECT SELECT button ENGLISH Rear INSTALLATION INSTRUCTIONS (continued) Installation and Cabling Connecting to the PC Read Usage Notes ( to ) carefully to ensure maximum safety before proceeding to these steps: Make sure that the display signals produced by your PC meet the specifications of this product. For the specifications of this product, see Product Specifications ( Installer le moniteur près d'une prise secteur. to ). ENGLISH Choose an appropriate site and install the product on a level table where the stand is secure. Make sure that the monitor's power switch is off. The monitor is shipped with the power switch off. Make sure that your PC's power switch is off. Interconnect the signal input terminal (RGB1) on the monitor rear panel and the display signal output terminal of the PC to each other using the signal cable included. Optional cables are needed to connect to the RGB2 input and audio input terminals. If the signal cable included does not match your PC, consult your dealer after reading the section "Signal Input". Insert one end of the power cable included into the rear-panel power cable connector and the other end into a power socket. Turn on the monitor, then the PC to make sure that a display image appears on the monitor screen. For instructions on turning on the monitor and adjusting its display images, see "Operating Instructions" ( to ). Monitor rear panel PC To audio output terminal To signal output terminal To signal output terminal Power cable Power cable connector AUDIO IN To audio input terminals RGB1 D-SUB IN RGB2 L/MONO R V H B G R RS232C IN To signal input terminals To signal input terminals Handling the Remote Controller ENGLISH With in 30 degrees About 5m SELECT Loading Batteries Open the battery cover. Slide the battery cover towards the arrow mark while pressing it. Load batteries. Load two Size AA batteries included observing the correct polarities. Close the battery cover. Slide back the battery cover towards the arrow mark. Handling the Remote Controller Use the remote controller within about 5 m from front of the unit's remote-control sensor and within 30 degrees on both sides. With in 30 degrees CAUTIONS Do not use new and old batteries together. The batteries could explode or leak, resulting in fires, physical injury, or stains. When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains. Do not drop or impact the remote controller. Do not splash the remote controller with water or put it on a wet object to avoid possible failures. Before leaving the remote controller out of use for an extended period of time, remove the batteries from it. If the remote controller begins to lack responsiveness, replace the batteries. Strong light such as direct sunlight impinging on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light. TIPS OPERATING INSTRUCTIONS Turning Power On and Off To turn on the set power supply, set the MAIN POWER switch ( ) of the main unit to ON and then press the SUB POWER button or the POWER button of the remote control. To turn off the set power supply, press the SUB POWER button of the main unit or the POWER button of the remote control, then set the MAIN POWER switch ( ) to OFF. For normal operations, leave the main power switch ( ) set to ON and use the sub power switch or the Power button of the remote control to turn the power on and off. Display lamp Off Lights red Power status Off Off (standby)* Operating When the main power switch ENGLISH is set to OFF. When the main power switch is set to ON and Power button of the remote control or the sub power button on the control panel located at the front part of the bottom plate is off. [. . . ] If the text appears blurred across the screen, make the adjustment instructed in Symptom 2. The display image may be momentarily disturbed during clock adjustment but this is not a failure. Symptom 2 Text displayed across the screen appears blurred in its entirety (display 2). A fine pattern flickers when displayed on the screen (display 3). Display 2 Before adjustment ABCDEFGHIJ abcdefgABCDEFGabcd ABCDEFGHIJ abcdefgABCDEFGabcd Display 3 Before adjustment ABC ABC Example After adjustment After adjustment ABC Adjustment procedure Press MENU button to open the adjustment menu. Press SELECT button several times to choose DISPLAY. [. . . ]