Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HITACHI CMPAT04. We hope that this HITACHI CMPAT04 user guide will be useful to you.
Lastmanuals help download the user guide HITACHI CMPAT04.
Detailed instructions for use are in the User's Guide.
[. . . ] This symbol indicates that incorrect handling due to ignoring this symbol can result in the possibility of personal injury and physical damage. This symbol indicates forbidden actions. This symbol indicates required actions.
WARNING CAUTION
This symbol indicates additional cautions (including warnings).
Caution (general)
Forbidden (general)
Disassembly prohibited
Required (general)
Indicates that the power plug is to be disconnected from the power outlet.
Safety Cautions
WARNING
When a malfunction occurs, disconnect the power plug from the power outlet and take measures to prevent other people coming near the plasma display.
Disconnect the power plug from the power outlet.
Contact your local dealer.
In the cases such as · The plasma display is loose and vibrates to an extreme degree, · Mounting screws or parts are loose or missing, failure to take appropriate actions can result in injury. [. . . ] Disassembly
· Slightly loosen the 4 lock screws and 1 rotation stopper screw. Merely slightly loosen the above screws. · Pull out the 2 snap pins and the 2 coupling pins. · Separate the ceiling mount unit and angle adjustment unit.
Ceiling mount unit remove the 2 coupling pins. Remove the 2 snap pins.
Loosen the 4 lock screws. Angle adjustment unit
(Front)
(Back)
2. Downward tilt angle adjustment
· Remove 1 M6 x 18 screw from each side of the angle adjustment unit. Align the hole for the necessary screen tilt angle and then tighten the M6 x 18 screws. Be sure that both the left and right sides are set to the same angle.
M6 X 18 screw
3. Installing on the ceiling
· Pass the wiring cable through the ceiling mount unit as necessary. · Install the ceiling mount unit on the ceiling with the cable hole facing the back. · For the ceiling, use commercially available bolts, washers and nuts that are appropriate for the ceiling construction.
Mounting hole: 12mm dia.
0 30
30
0
M10 bolt
Flat washer Spring washer Nut Cable hole Ceiling mount unit Wiring cable
-6-
4. Installing the angle adjustment unit
1. Pass the wiring cables through the pipe, then insert the angle adjustment unit into the ceiling mount unit. [. . . ] Display mount (left)
2nd plasma display hole from the top.
Stand
-8-
Installing the plasma display on the angle adjustment unit
To fasten the plasma display to the ceiling mount unit, engage the four pins of the angle adjustment unit in the four cutouts of the display mount fitting on the back of the plasma display. Next, tighten the two screws from the bottom. When installation is complete, fasten the wiring cable with cable clamps as necessary.
Pin Make sure that the pins and cutouts at both the top and bottom are firmly engaged. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HITACHI CMPAT04
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HITACHI CMPAT04 will begin.
