User manual HITACHI CP-X1200WA

[. . . ] KEYSTONE LENS SHIFT BNG COMPONENT S-VIDEO VIDEO STANDBY/ON TEMP LAMP RGB M1-D INPUT SEARCH RESET MENU FOCUS ZOOM INTER CP-X1200W/CP-X1250W Projector PORTUGUÊS NEDERLANDS NORSK ITALANO ESPAÑOL DEUTSCH FRANÇAIS ENGLISH Projector CP-X1200W/CP-X1250W Thank you for purchasing this projector. WARNING Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. [. . . ] : TURN ON TURN OFF When the TURN ON is selected, an S2-video signal can be identified and the optimum aspect ratio is automatically selected. memo This item is performs only at a S-VIDEO signal. memo When the ASPECT button is used or the item "ASPECT" of the MAIN menu is operated, the TURN OFF will be automatically selected to this item. Select the EXECUTE using the button to reset the INPUT menu items. : EXECUTE CANCEL The items of the INPUT menu are collectively returned to the initial setting. Note that the item "INFORMATION" is not reset. S2-ASPECT RESET 28 Multifunctional Settings (continued) AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description Pressing the (or the ENTER) button performs the automatic adjustment. At a RGB signal The vertical position (V POSITION), the horizontal position (H POSITION), the clock phase (H PHASE) and the horizontal size (H SIZE) will be automatically adjusted. memo Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. At a video signal The signal type mode best suited for the respective input signal will be selected automatically. memo This function is available only when the AUTO is selected to the item "VIDEO" of the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function. memo This operation requires approximately 10 seconds, and the message "AUTO IN PROGRESS" is displayed during the operation. memo This operation may not work well at some signals. a irregular picture, a color lack), please select the suitable mode to the item "VIDEO" of the INPUT menu. 99 minutes) AUTO POWER OFF ENABLE MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK : SELECT ADJUST POWER OFF POWER ON SEARCH RESET 0 min TURN ON TURN ON ADJUST buttons. 0 minute = DISABLE) AUTO POWER OFF DISABLE 0min POWER OFF ex. When the time is set to 1 to 99, the projector lamp will go off and the STANDBY/ON indicator begins blinking when the passed time with a proper signal (without no-signal and an unsuitable signal) reaches at the set time. Please refer to the section "Turning Off The Power". Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, you can turn the projector on without pressing the STANDBY/ON button. Please refer to the section "Turning Off The Power". [. . . ] Run a command. 7 RS-232CCommunication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (`02H'+`00H'+ type (2 bytes)+`00H'+`00H') from the computer to the projector. (2) The projector returns the response code `1DH'+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (`01H'+`00H'+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code `06H' to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data (`06H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. [. . . ]