User manual HITACHI CP-D10W TECHNICAL SPECIFICATIONS

[. . . ] INSTALLATION INSTRUCTIONS Short-Throw Projector Wall Mount Model: CPD10WALLARM NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1. 800. 368. 9700 Fax: 1. 800. 832. 4888 Other Locations Phone: (001). 714. 632. 7100 Fax: (001). 714. 632. 1044 9533-019-A03-00 EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 AUSTRALIA AND OCEANIA Distributed by Amber Technology Limited Unit B, 5 Skyline Place Frenchs Forest NSW 2086 Australia Phone: +61 2 9452 8600 Sydney Office Toll Free: 1-800-368-9700 Email: mounts@ambertech. com. au CPD10WALLARM Contents Weight Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (Example: A + B + C + 2. 5" = ?) C- Center of the lens to the top of the projector bracket. Add the measurements to determine the mounting height mark. Place a mark at the top of the total calculated height measurement starting from the ground up. This mark will represent the lower edge of the wall plate. Add 2. 5" to the calculated total. This total distance will be the location for the bottom rail on the wall plate. Projector Bracket Projector Lens Mark Top of Screen Ground Page 4 Visit Premier Mounts website at http://www. mounts. com Installation Instructions CPD10WALLARM Wood Stud Installation Step 1 THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION. Do NOT overtighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. Use a stud finder to determine the exact center of wall studs in the vicinity of the wall plate. Step 2 Use a pencil to mark the first mounting point, just above your height mark (from the "Determining the Installation Height" section). X X X X Mounting Point Mark Height Mark (from page 4) Step 3 Use the level to make sure the wall plate is level from side to side. Place the wall plate over the first mounting point mark and use a pencil to mark the rest of the mounting points. Two (2) upper mounting points and two (2) lower mounting points. Marking Level X X Wall Plate Step 4 Use a ¼" drill bit and portable drill to drill the pilot holes. X X X X Installation Instructions Visit Premier Mounts website at http://www. mounts. com Page 5 CPD10WALLARM Wood Stud Installation (cont'd) Step 5 Use four (4) 516 x 3" lag bolts and four (4) flat washers to mount the wall plate to the wooden studs. Use a ½" socket and socket wrench to finish this step. Lag Bolt and Flat Washer X Insert and gently tap the wall plate covers into place. X ½ Socket and Wrench Proceed to the "Removing the End Cover" section. Removing the End Cover Locate the end cover. Remove the M5 x 8mm security screw using a M5 security wrench (supplied). Proceed to the "Attaching the Projector Arm" section. CPD10WALLARM M5 x 8mm Security Screw End Cover Page 6 Visit Premier Mounts website at http://www. mounts. com Installation Instructions CPD10WALLARM Attaching the Projector Arm Step 1 Locate the mounting hook cutout on the top of the wall plate. Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts. Slowly lower and let the projector arm rest against the wall plate. If using the storage feature of the product, it may be easier to route any wiring at this time (please see the "Cable Management" section). MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT. Mounting Hook Cutout Mounting Hooks CPD10WALLARM Step 2 Locate the two (2) lock mounting points on the projector arm. These two points will be aligned with the lock mounting points on the wall plate. Using a security wrench, insert and tighten two (2) M5 x 8mm security head screws. Do NOT overtighten these screws. Lock Mounting Point Proceed to the "Extension Arm Installation" section. M5 x 8mm Security Head Screw Security Wrench Installation Instructions Visit Premier Mounts website at http://www. mounts. com Page 7 CPD10WALLARM Extension Arm Installation Please see the Operator's Manual to determine the correct throw distance (the distance from the projector to the screen). The throw distance must be determined prior to mounting the projector. Slide the extension arm into the open end of the CPD10WALLARM (the front of the mount). Adjust length so that the center of the adjustable mounting bracket matches the throw distance calibration. Line up the mounting holes on the extension arm with the mounting slots on the CPD10WALLARM. [. . . ] It may be easiest to pre-wire all cables down the arm (or extension) at this time. Open the storage door that is located on the side of the wall plate. Place the electronic components inside the storage enclosure. Make all electronic connections at this time. Electronic Components Door Step 2 Close the storage door and secure using two (2; 1 upper and 1 lower) M5 x 8mm security head screws. Tighten using a security wrench. Security Wrench M5 x 8mm Security Screw Repeat this process for the remaining side as well. Proceed to the "Cable Management" section. Door Electronic Components Page 12 Visit Premier Mounts website at http://www. mounts. com Installation Instructions CPD10WALLARM Cable Management The cable access holes are located at the end of the short throw mount and on the wall plate. [. . . ]