User manual HITACHI CPL750W

[. . . ] Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer. [. . . ] PLUG&PLAY is a system with computer, peripherals (including projectors), and operating system. It works when the projector is connected to DDC (Display Data Channel) ready computer that is running an operating system software that incorporates plug & play functionality. (Only RGB 1) 13 ENGLISH FREEZE Basic operations (continued) FREEZE FUNCTION This function can display a still picture (by freezing). This function can be used in combination with a MAGNIFY function. STANDBY/ON MUTE 1 2 Press the FREEZE button. 1, 2 FREEZE MAGNIFY VOLUME OFF POSITION ON LASER [TO RELEASE FREEZE] Press the FREEZE button. RESET MENU ON RIGHT MOUSE ON Caution Note: When the FREEZE Button is pressed, FREEZE and RELEASE can function alternately. A mark appears at the lower right of the screen for about 3 seconds during the FREEZE function. Furthermore, a mark appears at the bottom of the screen for 3 seconds or so when FREEZE is released. What is more, FREEZE is released when an input selector button is pressed or when the display mode of a personal computer is switched over during display. MAGNIFYING FUNCTION It is possible to display a partially magnified picture. This function can be used in combination with a FREEZE function. 1 2 3 4 5 6 14 Press the MAGNIFY + button. · By doing so, the center of the picture can be magnified as one part, becoming double in size. STANDBY/ON MUTE [TO CHANGE MAGNIFICATION] 1, 2 6 4 5 FREEZE MAGNIFY VOLUME OFF POSITION ON LASER Press the MAGNIFY + button. · When the button is pressed, more magnification of display takes place. (Maximum about 4 times) 3 RESET MENU ON BLANK RGB INPUT RIGHT MOUSE ON TIMER VIDEO Press the MAGNIFY - button. · When the button is pressed, the magnified display reduces its size. (Minimum about 1. 1 times) [TO SHIFT DISPLAY AREA] Press the POSITION ON button. Press the DISK PAD button up and down and left and right. · The magnified display area shifts in the direction the button is pressed. [TO RETURN TO NORMAL DISPLAY] Press MAGNIFY OFF button. Note: The MAGNIFY function is released when an input selector button is pressed or when the display mode of a personal computer is switched over during display. Caution Adjustments and functions STANDBY/ON MUTE STANDBY/ON INPUT MUTE MAGNIFY VOLUME OFF POSITION ON LASER MENU RESET 2, 3 RESET RIGHT MOUSE ON TIMER VIDEO INPUT 1, 2, 3 1 MENU ON BLANK RGB 1 2 3 Press the MENU ( OFF button. · On-screen menus are displayed on the screen. ) buttons or the MENU ON / Select the menu to be adjusted using the MENU ( buttons or DISK PAD. · Menu displayed in green is selected. ) Select the item to be adjusted using the MENU ( buttons or DISK PAD. · Item displayed in green can be adjusted. · Auto-adjustment will take about 10 to 15 seconds to complete. · In some cases auto-adjustment may not function normally, depending on the type of computer to which the unit is connected, and the signal sent. · Auto-adjustment may not perform normally with some images. Do not use with animated or dark images. · Carry out the auto-adjustment when the application, which is activated on the computer, is set to the maximum display. · After auto-adjustment the screen may become slightly dark due to the auto-adjustment of the signal level. INPUT The menu INPUT serves for the selection of input source. SETUP INPUT IMAGE OPT. SYSTEM AUTO NTSC PAL SECAM NTSC4. 43 M-PAL N-PAL RGB1 RGB2 VIDEO RGB1 RGB2 V I DEO Adjustment Item RGB 1 RGB 2 VIDEO Selects the RGB 1 terminal. Selects the VIDEO terminal. Details of adjustment SYSTEM Selects the video signal systems. When the picture (Video) is abnormal (no color), selects the input signal mode (NTSC, PAL, SECAM, NTSC4. 43 M-PAL and N-PAL). To input N-PAL signals, select N-PAL. 17 ENGLISH Adjustments and functions (continued) IMAGE SETUP INPUT IMAGE MIRROR BLANK REVEAL MESSAGE The menu IMAGE serves of the picture inversion. OPT. SETUP INPUT IMAGE OPT. MIRROR NORMAL H : INVERT V : INVERT H&V : INVERT BLANK WHITE BLUE BLACK SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. REVEAL FAST MEDIUM SLOW MESSAGE TURN ON TURN OFF Adjustment Item Details of adjustment Inverts the picture horizontally or vertically. [. . . ] If the lamp does not light because it is still automatically turned off, contact your dealer. *2 If temperature inside the unit increases because of blocked vets, the lamp may go off for protection, and the LAMP indicator will turn red. Should this happen, turn off the main switch, wait until the set cools down (about 45 minutes), then again turn on the main switch. When you think something wrong Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer. Phenomena Cause Check point Page P. 12 P. 8 P. 12 Power cannot be turned on. ·Turn the MAIN POWER switch on. [. . . ]