User manual HITACHI CP-X325

[. . . ] Liquid Crystal Projector ENGLISH USER'S MANUAL Thank you for purchasing this liquid crystal projector. Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE: · The information in this manual is subject to change without notice. · The manufacturer assumes no responsibility for any errors that may appear in this manual · The reproduction, transmission or use of this documents or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT: · PS/2, VGA and XGA are registered trademark of International Business Machines Corporation. [. . . ] · Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. ENGLISH-14 OPERATIONS (continued) SETUP INPUT IMAGE OPT. 128 The following adjustments and settings are available when OPT. Select an item with the and buttons, and start operation. VOLUME MENU COLOR TIMER LANGUAGE AUTO OFF SYNC ON G Table 6. Options Menu Item VOLUME MENU COLOR TIMER Description Volume adjustment: Reduce VOLUME Increase VOLUME Select menu background color: Select with the Operation start/stop: Press the or button. Setup initial timer value: Set 1~99 minutes with the and buttons. Operation start/stop: Press the or button. Select menu display language: Select with the and buttons. LANGUAGE and buttons. AUTO OFF Operation start/stop: Press the or button. Set AUTO OFF: Set 1~99 minutes with the and buttons. The system automatically enters the standby mode when a signal is not received for the set time. Clear AUTO OFF: Select STOP (0 min. ) with the button. Wind Stop is selected the system does not enter the standby mode even if no signal is received. Operation start/stop: Press the or button. SYNC ON G valid: Select TURN ON with the button. SYNC ON G invalid: Select TURN OFF with the button. · May not be displayed correctly with some input signals when SYNC ON G is valid. In such cases, remove the signal connector so that knows signal is received, set SYNC ON G to invalid, and reconnect the signal. SYNC ON G ENGLISH-15 ENGLISH Options Menu OPERATIONS (continued) No Signal Menu The same adjustments and settings are available as with the Image and Options menus when the MENU button is pressed during display of the "NO INPUT IS DETECTED ON ***" or "SYNC IS OUT OF RANGE ON ***" message while no signal is received. VOLUME KEYSTONE BLANK MIRROR START UP MENU COLOR TIMER LANGUAGE AUTO OFF SYNC ON G 40 +1 Table 7. No Signal Menu Item VOLUME KEYSTONE Description Volume adjustment: Reduce VOLUME Adjustment: Reduce size of bottom of image Increase VOLUME Reduce size of top of image Select blank screen color: Select color with the BLANK and buttons. · When the blank mode is set with BLANK ON, by absence of a signal, or by input of a non-standard signal, the image is cleared and the complete screen is displayed in the selected colour. Note that if No Display is selected in Initial Screen the blank screen is displayed in blue when no signal is received. MIRROR Operation start/stop: Press the or button. Select Mirror status: Select mirror status with and buttons. START UP Operation start/stop: Press the or button. Setup initial screen display: Select TURN ON with the button. Clear initial screen display: Select TURN OFF with the button. · Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. [. . . ] (2) The projector changes the specified setting to the default value. (3) The projector returns the response code `06H' to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data (`04H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+`00H'+ type (2 bytes) +`00H' + `00H') to the projector. [. . . ]