User manual HITACHI DVP250U

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. LOCATION: INSIDE, NEAR THE DECK MECHANISM. FCC WARNING- This equipment may generate or use radio frequency energy. [. . . ] The set up screen is displayed. TIMER PROGRAMMING PROG 12345678 DATE START TIME END TIME CHANNEL REC SPEED ¡TV STEREO or SAP is selected. NORMAL RECORDING VCR 1 Begin the recording by pressing RECORD. The REC Light comes on. ¡To temporarily stop recording or to resume it, press 4 Set the timer. ¡To go back one step, press s. PAUSE/STEP. After the VCR has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage. 1) Set the program number (1-8) 2 Press STOP when the recording is completed. Note ¡When you wish to watch another program while Program number which is not set up flashes. Press K or L repeatedly for the desired program number. Then, press B. PROGRAM NUMBER 4 DATE --/-START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - recording, select desired channel on your TV. If noise appears press VCR/TV. 2) Set the frequency of the recording IRT (Instant Recording Timer) VCR This feature allows you to set the recording length simply by pressing REC/IRT on the VCR. For once: Press K or L to point to "ONCE". For daily (Monday~Friday): Press K or L to point to "DAILY". For weekly: Press K or L to point to "WEEKLY". Then, press B. 3) Set the date PROGRAM NUMBER 4 ONCE DAILY WEEKLY 3 Press REC/IRT to begin IRT. Change the recording length by pressing REC/IRT repeatedly. REC (Normal recording) IRT(8:00) IRT(0:30) IRT(1:00). . . . . First, press K or L for the month. Press VCR/TV to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual. H9450UD(EN). qx33 03. 1. 22 7:19 PM Page 22 SPECIAL FEATURES ¡Always use video-quality shielded cables with COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording DVD/VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording DVD/VCR] (this unit) DVD/VCR VCR RCA-type connectors. Standard audio cables are not recommended. ¡You can use a video disc player, satellite receiver, camcorder or other audio/video component with A/V outputs in place of the playing VCR. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See "RF Output Channel" on page 13 for the detail). 2 Press VCR/TV on the remote control of the recording DVD/VCR. DVD S-VIDEO CONPONENT AUDIO VIDEO OUT OUT OUT L AUDIO OUT AUDIO IN DIGITAL AUDIO OUT ANT-IN L MTS (Multi-Channel Television Sound) SYSTEM VCR When you play a VHS tape, or receive a broadcast on the VCR tuner channel you are watching, the current status will 1)* appear when you press DISPLAY on the remote control. When you record a MTS broad2)* cast signal, you need to set it to MTS mode. STOP 12:00AM CH 32 STEREO SAP SP 0:00:00 HIFI Y R ANT-OUT VIDEO OUT VIDEO IN R I P CB PB CR PR L COAXIAL R PROGRESSIVE Coaxial cable (supplied) [TV set] (Use for monitoring) Audio/Video cables (not supplied) OUT IN LEFT RIGHT AUDIO VIDEO ANT in [Playing VCR] (another source) 1 Insert a pre-recorded tape into the playing VCR. 1)* Press MENU and select "TV STEREO" or "SAP" by pressing K or L. [. . . ] Luego presione B. 1) Ajuste el mes Presione o o p repetidamente. Luego presione B. 2) Ajuste el día 1 Presione y/I. ¡Aparecerá "Load" brevemente en el visualizador. ¡Asegúrese que la luz DVD OUTPUT está encendida. [. . . ]