User manual HITACHI ED-X52

[. . . ] Projector ED-X50/ED-X52 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read all manuals for this product. Be sure to read "Safety Guide" first. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. [. . . ] Please move the frame to the position of the image which you want to use. The frame may not be able to be moved for some input signals. To start registration, press the ENTER or INPUT button on the remote control. To restore the screen and return to the previous dialog, press the RESET button on the remote control. When the registration is completed, the registered screen and the following message is displayed for several seconds: "MyScreen registration is finished. " If the registration failed, the following message is displayed: "A capturing error has occurred. Please try again. " · This function cannot be selected when the ON is selected to the MyScreen Lock item ( 41). · This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu ( 51). MyScreen (continued on next page) 40 SCREEN menu Item Description Using the / buttons turns on/off the MyScreen lock function. ON OFF When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen. · This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu ( 51). Using the / buttons turns on/off the message function. ON OFF When the ON is selected, the following message function works. "AUTO IN PROGRESS" while automatically adjusting "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "INVALID SCAN FREQ. " "Searching. . . . " while searching for the input "Detecting. . . . " while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of "FREEZE" and "II" while freezing the screen by pressing the FREEZE button. The indication of the TEMPLATE displayed by changing. · When the OFF is selected, please remember if the picture is frozen. Do not mistake freezing for a malfunction ( 23). MyScreen Lock MESSAGE (continued on next page) 41 SCREEN menu Item Description Each input port for this projector can have a name applied to it. (1) Use the / buttons on the SCREEN menu to select SOURCE NAME and press the or ENTER button. (2) Use the / buttons on the SOURCE NAME menu to select the port to be named and press the button. The SOURCE NAME dialog will be displayed. Right side of the menu is blank until a name is specified. (3) Select an icon you'd like to assign to the port in the SOURCE NAME dialog. The name assigned to the port will also be automatically switched according to your icon selection. [. . . ] sync / Composite sync. , (No connection) V. sync. , (No connection) A : SCL (DDC clock), (No connection) B , C : (No connection) 3 Connection to the ports (continued) D E D S-VIDEO Mini DIN 4pin jack 4 2 3 1 · System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4. 43, PAL (60Hz) Pin 1 2 3 4 Signal Color signal 0. 286Vp-p (NTSC, burst), 75 terminator Color signal 0. 300Vp-p (PAL/SECAM, burst) 75 terminator Brightness signal, 1. 0Vp-p, 75 terminator Ground Ground E VIDEO RCA jack · System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4. 43, PAL (60Hz) · 1. 0±0. 1Vp-p, 75 terminator 4 Connection to the ports (continued) F H G F AUDIO IN1, G AUDIO IN2 Ø3. 5 stereo mini jack · 200 mVrms 47k terminator H AUDIO OUT Ø3. 5 stereo mini jack · 200 mVrms 1k output impedance 5 Connection to the ports (continued) I J I USB USB B type jack Pin 1 2 3 4 +5V - Data + Data Ground Signal 2 1 3 4 J CONTROL D-sub 9pin plug · About the details of RS-232C communication, please refer to the following page. Pin 1 2 3 RD TD Signal (No connection) Pin 4 5 6 Signal (No connection) Ground (No connection) Pin 7 8 9 RTS CTS (No connection) 98 76 54321 Signal 6 Connection to the ports (continued) To input component video signal to COMPUTER IN ports ex. D-sub plug RCA plugs RCA connectors Y CB/PB CR/PR COMPONENT VIDEO OUT VCR/DVD/Blu-ray Disc player To input component video signal to the COMPUTER IN1 or IN2 port of the projector, use a RCA to D-sub cable or adapter. For about the pin description of the required cable or adapter, refer to the descriptions about COMPUTER IN1 and IN2 port ( 3). 7 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. [. . . ]