User manual HITACHI L26A01

[. . . ] LCD Colour Television Télévision Couleur LCD LCD-Farb-TV-Gerät Televisione a Colori LCD Instructions for use Notice d'utilisation GB F D I L26A01 Bedienungsanleitung Istruzioni per l'uso Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LCD TV Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Do not place the remote control under the direct sunlight or near sources of excessive heat. Operating Range for the Remote Control · Point the top of the remote control toward the LCD TV's remote sensor LED while pressing a button. Connections To The Aerial Input Socket · Connect the aerial or cable TV plug to the Aerial input socket located at the rear of the TV and connect the cable plug coming out from the TV out socket located on the devices (VCR, DVB etc. ) to this socket as well. Inserting Batteries In The Remote Control Handset WARNING : Remote control is battery included. A plastic protector is used to disconnect the batteries in order to prevent the battery life from reducing. Please remove the plastic protector before the first use. · Remove the battery cover located on the back of the handset by gently pulling backwards from the indicated part. · Insert two AA/R6 or equivalent type batteries inside. Place the batteries in the right directions and replace the battery cover. RG B2 30 30 TV / TT D D VD SAT I PUT N AV 1 1 AV 4 4 H DM I 2 7 AV 2 2 AV 5 5 8 0 II /I AV 3 3 HDM I 1 6 9 P . . . . M EN U G UI E D OK RE TUR N + Remote range is approximately 7m/23ft. -9- Switching The TV ON/OFF To switch the TV on: Your TV will switch on in two steps: 1- Connect the power cord to the system. Then the TV switches itself to stand-by mode (optional). 2- To switch on the TV from stand-by mode either: Press a digit button on the remote control so that a programme number is selected, or Press the "-P/CH" or "P/CH+" button on the TV or press the P+ or Pbutton on the remote control, so that last mode switched off is selected. By either method the TV will switch on. Initial Settings When the TV is turned on for the first time, Auto Programme menu will be displayed on the screen Because this is the first time the TV is used, there are no channels stored in the memory and the following message appears on the screen. Auto Program Country Language TXT Language PLEASE CHECK ANTENNA CABLE AUTO. PROGRAMMING SYSTEM To switch the TV off: · Press the " (stand-by)" button on the remote control or On/Off switch on the TV, so the TV will switch to stand-by mode. To power down the TV completely, press On/Off switch or, Unplug the power cord from the mains socket. UK Ok Cancel Navigating the Menu System For Displaying Menu Options MENU GUIDE For Navigation OK By pressing or button, adjust the Country item to highlight "Language" item. Use and press or button to set "Language". Use or buttons to select "TXT Language" and set it by using or buttons. Press "OK" button to continue: For more information on this process, see "Install Menu" section. RETURN + Basic Operations To Confirm Choices You can operate your TV using both the remote control and onset buttons. Operation with the buttons on the TV 1- Press 2- Press / to display the menu. button to select an icon. Volume Setting · Press - button to decrease volume or + button to increase volume, so a volume level scale (slider) will be displayed at the middle of the bottom on the screen. / button to highlight. Press for more 3- Use options in analogue TV mode. Use OK in DTV mode for viewing a submenu. 5- To exit the menu or return from sub-menu screen, press . These explanations are available for the navigation of the whole menu system. To select options that are explained in the following parts, refer to "Navigating The Menu System". Programme Selection · Press P/CH + button to select the next programme or P/CH - button to select the previous programme. Entering Main Menu · Press the MENU button to enter Main menu. In the Main menu select sub-menu using P/CH - or P/CH + - or buttons and enter the sub-menu using + buttons. [. . . ] sync. on Green * Priority 1 2 3 S-input connector pin specifications Pin 1 2 3 4 Frame Input signal Y Y-GND C C-GND GND · Even in the case of the recommended signals shown on the following page, there may be instances when correct display is not possible. In this case, use H/V separate sync, H/ V composite sync. HDMI connector pin specifications Pin 1 2 3 4 5 6 7 8 9 10 Input signal TMDS Data2+ TMDS Data2 Shield TMDS Data 2TMDS Data 1+ TMDS Data1 Shield TMDS Data1TMDS Data0+ TMDS Data0 Shield TMDS Data0TMDS Clock+ Pin 11 12 13 14 15 16 17 18 19 Input signal TMDS Clock Shield TMDS ClockCEC Reserved (N. C. on device) SCL SDA DDC/CED Ground +5V Power Hot Plug Detect SCART connector pin specifications Pin 1 2 3 4 5 6 7 8 9 10 11 Input signal AUDIO OUT (RIGHT) AUDIO IN (RIGHT) AUDIO OUT (LEFT/MONO) AUDIO GND RGB-B GND AUDIO IN (LEFT/MONO) RGB-B IN AUDIO / RGB SWITCH / 16:9 RGB-G GND Not used RGB-G IN Pin 12 13 14 15 16 17 18 19 20 21 Input signal Not used RGB-R GND GND RGB-R / S. VHS CHROMINANCE IN BLANKING SIGNAL COMPOSITE VIDEO GND BLANKING SIGNAL GND COMPOSITE VIDEO OUT COMPOSITE VIDEO / S. VHS LUMINANCE IN GND / SHIELD (CHASSIS) - 25 - Appendix A: PC Input Typical Display Modes The display has a maximum resolution of 1360 x 768, frequency range of 56-75 Hz. The following table is an illustration of some of the typical video display modes. Mode 1 2 3 4 5 6 7 8 9 10 11 12 13 Resolution Frequency Horizontal Vertical Hor. (kHz) Ver. (Hz) 640 640 640 800 800 800 800 1024 1024 1024 1280 1280 1360 480 480 480 600 600 600 600 768 768 768 1024 768 768 31, 5 37, 9 37, 5 35, 2 37, 9 48, 1 46, 9 48, 4 56, 5 60 64 47, 8 47, 7 60 72 75 56 60 72 75 60 70 75 60 60 60 - 26 - Appendix B: AV and HDMI Signal Compatibility Source AV-1 (SCART 1) Supported Signals PAL 50/60 NTSC 60 RGB 50 RGB 60 PAL 50/60 NTSC 60 RGB 50 RGB 60 PAL 50/60 NTSC 60 S-VHS 50 S-VHS 60 PAL 50/60 NTSC 60 PAL 50/60 NTSC 60 480I 60Hz 480P 60Hz 576I 50Hz 576P 50Hz 720P 50Hz 720P 60Hz 1080I 50Hz 1080I 60Hz 480I 60Hz 480P 60Hz 576I 60Hz 576P 60Hz 720P 60Hz 720P 50Hz 1080I 50Hz 1080I 50Hz 1080P 50Hz 1080P 60Hz 1080P 24 HZ AV-2 (SCART-2) AV-3 (SCART-3) AV-4 FAV AV-4S (S-Video) AV-5 YPbPr HDMI1 HDMI2 Available O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O X X X (X: Not Available, O: Available) Note: In some cases a signal on the LCD TV may not be displayed properly. [. . . ]