User manual HITACHI L32HK04UA

[. . . ] 2 Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Disconnecting the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please do refer to the "TELETEXT" explanations. Widescreen Depending on the type of the broadcast being transmitted, programmes can be viewed in a number of formats. Press the "SCREEN" button repeatedly to change screen format. When Auto is selected, the format being displayed is determined by the picture being broadcasted. PLEASE NOTE: Menu size changes depending on the chosen image size. Navigating the Entire Channel List Press " " or " " button for selecting the previous or next channel. You can press "RED" or "GREEN" button to move page up or page down. To watch a specific channel, highlight it using " " or " " button and then press "OK" button, while the "Select" item on Channel List menu is highlighted by using " " or " " button. Then the name and number of the selected channel will be displayed in the top-left and top-right of the channel display at the top-right of the screen, respectively. Notice ! AC3 audio type is not supported. If the broadcast includes AC3 stream, the following warning message will be displayed on the screen: Moving the channels in the channel list · Press " " or " " buttons to select the channel that will be moved. · Press " " or " " buttons to select the "Move" item on Channel List menu. Following OSD will be displayed next to "OK" item to indicate that enter a number by using the numeric buttons on the remote control and press "OK" to confirm. If there is no audio available, the following warning message will be displayed on the screen:. English - 13 - Now pressing " " or " " button moves to the previous/ next character. Pressing " " or " " button toggles the current character, i. e. , `b' character becomes `a' by " " and `c' by " ". Pressing the numeric buttons `0. . . 9' replaces the highlighted character with the characters printed above the button one by one as the button is pressed. These require a subscription and a hardware decoder. Obtain the Conditional Access Module (CAM) and the viewing card by subscribing to a pay channel company, then insert those to the TV using the following procedure. · Switch off the TV and unplug from the mains. · The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. · Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. · Some CAMs may require the following set up. Please set the CAM by entering the IDTV menu, Conditional Access then pressing the "OK" button. (CAM set up menu is not displayed when it is not required. ) · To see the viewing contract information: enter IDTV; press the "MENU" button, then highlight Conditional Access and press the "OK" button. · When no module is inserted, "No Conditional Access module detected" message appears on the screen. · Refer to the module instruction manual for details of the settings. Note: Insert or remove the CI module only when the TV is switched off or in standby mode. Program Guide This section is same with the instructions given in the General Operations page. [. . . ] Check if you have entered the correct frequency. The picture quality may degrade when two peripherals are connected to the TV at the same time. In such a case, disconnect one of the peripherals. No Picture Is the aerial connected properly?Are the plugs connected tightly to the aerial socket? [. . . ]