User manual HITACHI PWT001

[. . . ] This plasma TV wall-mount unit is for use with the following models: HITACHI Plasma TV CL32-PD2100, CL37-PD2100, CL42-PD2100, 32PD5100, 42PD5100, 42PMA500 32PD5000, 32PD5200, 32PD5300, 37PD5200, 42PD5000, 42PD5200, 42PD5300, CMP4211/2, CMP4213/4 Special techniques are necessary for installation of the plasma TV. I Do not attempt to perform this work by yourself. I Request an installation specialist to install this unit. I This company assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling. [. . . ] Surround the area with rope, etc. , to prevent other people coming near. Contact your local dealer. Disconnect the power plug from the power outlet. Contact your local dealer. I Ask your dealer to install, move or adjust the angle of the wall-mount unit. Incorrect installation or adjustment can cause the plasma TV to fall. Handling by other than professional contractors is prohibited. ­2­ Installation Location WARNING Plaster board or thin ply wood, etc. I The wall where the wall-mount unit is to be installed must be capable of long-term support of the total load of the plasma TV and wall-mount unit. Measures should also be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. Incorrect installation can cause the plasma TV to fall and cause injury. Total load of the (plasma TV + wall-mount unit) = 26kg···CL32-PD2100 34kg···CL37-PD2100 37kg···CL42-PD2100 G Installation on a wooden wall Pillar or thick ply wood. Always install so that the load is supported by a pillar. If the strength of the pillar is insufficient, add reinforcement. Do not install on decorative posts or plaster board. G Installation on a concrete wall Use commercially available anchors that are capable of fully supporting the load of the plasma TV. CAUTION I Avoid installing in locations where the temperature and humidity are excessively high, and where contact with water is possible. These can result in fire or electrical shock. 10cm or more I Do not block the ventilation holes. Also provide sufficient clearance in regard to the surroundings to avoid blocking the ventilation. 10cm 10cm or more or more The internal temperature could elevate and possibly result in fire. I Do not install close to an airconditioner intake or outlet. Do not install in locations where there is excessive amounts of dust, oily smoke or tobacco smoke. Fire could result. I Install only on a vertical surface. Also, do not install facing upward. The internal temperature could elevate and possibly result in fire. Injury or damage could also result from falling. ­3­ CAUTION I Do not install in locations where there is excessive vibration or impact. Injury and damage could result from falling. I Do not install where there is direct sunlight and other strong light. Strong light could result in eye fatigue during usage. Installing WARNING I Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the plasma TV falls. I Make sure the TVmount metals and wall-mount metals are firmly engaged. Failure to do so could cause the plasma TV to fall. I Do not alter any of the parts. And do not use broken parts. This could result in injury due to the plasma TV falling. I Always use at least two people to perform the installation work. Injury could result from dropping heavy objects. I Use care to prevent the fingers being caught. Installation Method Assembling the wall-mount metals I Assemble the wall-mount metal (Top), (Center) and (Bottom) with 4 M6 x 18 screws. M6 x 18 screw x 4 cutout Wall-mount metal (top) Wall-mount metal (center) Wall-mount metal (bottom) ­4­ Mounting the wall-mount unit on the wall 1. Prepare at least four sets of commercially available anchors and screws, etc. , for various types of walls. Carefully read the safety cautions concerning installation locations as described in this instruction manual and then select a suitable location for installation. The relationship between the plasma TV exterior and center, and the positions of the wall-mount unit mounting holes is shown in the diagram for the various models. Install the anchors in the wall as shown in the diagram and process the holes as necessary. G Make sure that the strengths of the wall and the screws are fully sufficient. 32 inch 37 inch ­5­ 42 inch 4. Fasten the wall-mount unit securely to the wall. [. . . ] Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 ­12 Nishi Shinbashi, 2 ­ Chome, Minato ­ Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer -service@hitachi-eu. com HITACHI EUROPE S. A. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service. hellas@hitachi-eu. com HITACHI EUROPE GmbH Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München GERMANY Tel: +49-89-991 80-0 Fax: +49- 89-991 80-224 Hotline: +49-180-551 25 51 (12ct/min) Email: HSE- DUS. service@hitachi-eu. com HITACHI EUROPE S. A. [. . . ]