User manual HITACHI ULTRASTAR 2ES QUICK INSTALLATION GUIDE

[. . . ] IBM storage products Quick installation guide Ultrastar 2ES SCSI Models: DCAS-32160 DCAS-34330 Handling precautions 1. Covering the breather hole may result in loss of data. Installation procedure It is advisable to backup all data before proceeding with the installation. This procedure may require the use of a bootable System Diskette containing FDISK. COM and FORMAT. COM Setting the address 1. [. . . ] Turn off and unplug your computer before removing the case. When you are installing the drive, touch the static-protective package containing the drive to a grounded, unpainted metal surface for at least two seconds. (This drains static electricity from the package and from your body. ) 7. Handle the drive carefully by the edges. Do not touch any exposed printed circuit board. Save your drive packaging materials including the ESD bag in the event that the drive must be returned. Place the drive in an anti-static bag before placing it in the shipping container. The warranty will be void if the drive is not returned in IBM approved packaging. Ground 23 (1) 24 21 (2) 22 19 (3) 20 17 (4) 18 15 (5) 16 13 (6) 14 11 (7) 12 9 (8) 10 7 (9) 8 5 (10) 6 3 (11) 4 BIT3 BIT2 BIT1 BIT0 Enable Auto Spin Up Enable SCSI Terminator (50, 68 pin) Disable Unit Attention Enable TI-SDTR/WDTR Enable Auto Start Delay Delay Start 6/12 Disable SCSI Parity Check LED Cathod LED Anode 1 (12) 2 Note: JP1 is reserved on the 50-pin models Page 1 IBM Hard Disk Drive Technical Support Center version 3. 0 IBM storage products 2. The maximum screw insertion depth for bottom mounting is 6. 0 mm (. 23 in) and for side mounting is 3. 5 mm (. 14 in). Plug in the power cord and power on your computer. Consult your SCSI adapter users guide for information on configuring a new hard disk drive. Follow the Operating System instructions to format and partition your drive. If your system will not boot up after complete installation, recheck all settings. If the system still fails to boot up, remove the new drive to return the system to its original configuration and call the IBM Hard Disk Drive Technical Support Center. Power Connector Logic Card SCSI I/F Connector Back side of drive JP1 Option block JP12 Note: In the table below, "off" means a jumper is not in place and "on" means a jumper is in place. Bit 3 off off off off off off off off on on on on on on on on Bit 2 off off off off on on on on off off off off on on on on Bit 1 off off on on off off on on off off on on off off on on Bit 0 off on off on off on off on off on off on off on off on Address 0 1 2 3 4 5 6* 7 8 9 10 11 12 13 14 15 ® © International Business Machines Corporation 1999 www. ibm. com/harddrive IBM Hard Disk Drive Technical Support Center Dept. D8M 3605 Highway 52 North Rochester, MN 55901 Telephone: 888. IBM. 5214 or 507. 286. 5825 Fax: 507. 253. DRIVE E-mail: drive@us. ibm. com Singapore Technical Support Center Telephone: 1800. 418. 9595 or 65. 6. 418. 9595 E-mail: drive@sg. ibm. com IBM Systems Storage Division 5600 Cottle Road San Jose, CA 95193 www. ibm. com/storage Asia-Pacific Headquarters: 65. 320. 1234 European Headquarters: 44. 01. 705. 561. 871 Japan Sales Branch Office: 81. 46645. 1039 Printed in the United States of America 01-99 All Rights Reserved IBM is the registered trademark of International Business Machines Corporation. Other company, product, and service names may be trademarks or service marks of others. [. . . ] If the drive is attached to a cable that contains other devices and the new drive is not attached to the end of the cable, jumper position 6 must be open and Active Termination must be supplied by the device at the end of the cable. Select the other option jumpers as required by your computer. Mount the drive securely, using the appropriate brackets or rails, in any axes, using four 6-32 UNC metric screws in the bottom or side mounting holes. Page 2 IBM Hard Disk Drive Technical Support Center version 3. 0 [. . . ]