User manual HITACHI ULTRASTAR 36XP QUICK INSTALLATION GUIDE

[. . . ] Each drive on the SCSI bus must have a unique address. Sixty eight and eighty pin (Wide SCSI) devices have 16 possible addresses. SCSI address bits 3, 2, 1, and 0 of the 32 pin Option Jumper Block are used to select the SCSI device ID. Force Single Ended Mode External Activity LED Write Protect Ground Auto Start Blank Reserved SCSI ID Bits 3210 13 5 7 Auto Start Delay Disable Sync Negotiations Disable SCSI Parity Disable Unit Attention Disable Wide Negotiations 2. [. . . ] Place the drive in an anti-static bag before placing it in the shipping container. The warranty will be void if the drive is not returned in IBM approved packaging. 24 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Ground Reserved +5V Ground Termination Power Enable Ground Note: In the table below, "off" means a jumper is not in place and "on" means a jumper is in place. Bit 3 off off off off off off off off on on on on on on on on Bit 2 off off off off on on on on off off off off on on on on Bit 1 off off on on off off on on off off on on off off on on Bit 0 off on off on off on off on off on off on off on off on Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Installation procedure It is advisable to back up all data before proceeding with the installation. Page 1 IBM Hard Disk Drive Technical Support Center version 2. 0 IBM storage products 2. To format the primary system drive, type FORMAT C:/S at the DOS command prompt and press [ENTER]. The /S parameter makes C: the operating system startup drive. To format a second drive (not C:), type FORMAT X: (where X is the drive letter assigned by FDISK) at the DOS prompt and press [ENTER]. Remove the diskette and restart your computer. If your system will not boot up after complete installation, recheck all settings. If the system still fails to boot up, remove the new drive to return the system to its original configuration and call the IBM Hard Disk Drive Technical Support Center. 68 Pin Auxiliary Connector :::::: SCSI Address ID2 +5V 11 9 ID3 7 ID0 ID1 531 12 10 8 Write Protect Ground 642 Unused Reserved External Activity LED Auto Spin Start ® © International Business Machines Corporation 1999 www. ibm. com/harddrive IBM Hard Disk Drive Technical Support Center Dept. D8M 3605 Highway 52 North Rochester, MN 55901 Telephone: 888. IBM. 5214 or 507. 286. 5825 Fax: 507. 253. DRIVE E-mail: drive@us. ibm. com Singapore Technical Support Center Telephone: 1800. 418. 9595 or 65. 6. 418. 9595 E-mail: drive@sg. ibm. com IBM Systems Storage Division 5600 Cottle Road San Jose, CA 95193 www. ibm. com/storage Asia-Pacific Headquarters: 65. 320. 1234 European Headquarters: 44. 01. 705. 561. 871 Japan Sales Branch Office: 81. 46645. 1039 Printed in the United States of America 01-99 All Rights Reserved IBM is the registered trademark of International Business Machines Corporation. Other company, product, and service names may be trademarks or service marks of others. Produced by the IBM Hard Disk Drive Technical Support Center. OEM Hardware/Functional Specification, version 1. 02 Parallel SCSI Disk Drive Logical Interface Specification, release 1. 2 Product Description data represents IBM's design objectives and is provided for comparative purposes; actual results may vary based on a variety of factors. This product data does not constitute a warranty. Questions regarding IBM's warranty terms or methodology used to derive this data should be referred to the IBM Hard Disk Drive Technical Support Center. Date: 11 January 1999 Attaching the drive 1. Turn off the computer, unplug the power cord, and open the case. [. . . ] Follow the Setup menu to configure your computer with your new SCSI drive. It may be necessary to restart your computer for the changes to take effect. Partitioning and formatting (using DOS 5. 0 or later) Caution: Be sure that you select the correct hard drive. [. . . ]