User manual HITACHI VTL1100E

[. . . ] ENGLISH PRECAUTIONS Safety · Should any solid object or liquid fall into the cabinet, turn off the unit and have it checked by qualified personnel before operating it any further. · To disconnect the mains lead, pull it out by the plug. Installation · Choose a location in which air can pass through the ventilation holes in the bottom, top and back of the unit to prevent it from overheating. · Do not install the unit near heat sources such as radiators or air ducts or in a place subject to direct sunlight, excessive dust, mechanical vibrations or shock. [. . . ] The first program event location of MON flashes. Press the UP or DOWN button until the desired program number appears on the monitor. The other program event location of MON flashes on/off. Press the UP or DOWN button until the desired program number appears on the monitor. Notes: · If you do not need to timer record two events a day, mark either event with an asterisk (). · If two asterisks are displayed, no timer recording is made on that day. After setting two program event locations of MON, press the SET button. The two program event locations of the next day of the week flashes on/off. The first program event location of the next day flashes. Repeat steps 12 through 16 to set the program event locations up to SUN. Press the START/STOP button when the TIMER has been set. Notes: 1. After selecting, press the START/STOP button. 15 TAPE END (ON or OFF) · To specify whether buzzer turns on or off, synchronized with pin 4 TAPE END OUT of the EXTERNAL INTERFACE jack. ON: Buzzer will keep sounding when tape reaches the end during recording. OFF: Buzzer will not sound even when tape reaches the end. TROUBLE (ON or OFF) · To specify whether buzzer turns on or off when abnormality occurs in this VCR. ON: Buzzer will keep sounding if abnormality occurs. OFF: Buzzer will not sound even if abnormality occurs. NO VIDEO (ON or OFF) · To specify whether buzzer turns on or off when no video signal is input during recording. ON: Buzzer will keep sounding when video signal input stops. OFF: Buzzer will not sound even when input stops. AUTO REC CHECK (ON or OFF) · To specify whether buzzer turns on or off if recording is abnormal after the AUTO REC CHECK function. ON: Buzzer will keep sounding if recording is abnormal. [. . . ] If the components indicated C/R do not function normally after cleaning, replace them. Please contact the dealer for detail information. Maintenance Table Component and point Cylinder motor assembly A/C head assembly FE head S guide roller T guide roller Tension band brake Tension arm S reel table T reel table PR arm Timing belt Capstan motor Loading motor assembly Mechanism state switch Idler gear 1 Idler gear 2 FR gear JOG Gear Supply slant pole Take-up slant pole Tape guides Tape guide line on lower cylinder Tension band R FS brake HC arm Shaft and bearing of S reel table Shaft and bearing of T reel table Shaft and bearing of idler gear 1 Shaft and bearing of idler gear 2 Shaft of pulley assembly Shaft of torque change gear and FR drive gear Shaft of PR arm G base assembly moving portions in chassis Contact surface between cylinder base and G base assembly during loading R: Component replacement C: Cleaning S: Oil (Sonic Slidas oil) refilling M: Grease (Molicoat) refilling S S S S S S M S S S S S S M M M C C C C C C R R R C/R C C C C R C/R C C C C C C C C C 1000h C/R C C C C 2000h R C/R C C C R C C C R C R C C C 3000h C/R C C C/R C/R 4000h R R R C C R C C C R C R R (R) R R R C/R C C C C R C/R C (R) C C C C C C C C 5000h C/R C C C C 24 ENGLISH SOME DO'S AND DON'TS ON THE SAFE USE OF EQUIPMENT This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. 5555555555 DO read the operating instructions before you attempt to use the equipment. [. . . ]