User manual HITACHI VTM920EUK

[. . . ] 1-800-HITACHI (1-800-448-2244) Printed in China TABLE OF CONTENTS IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · The VCR distinguishes between standard TV channels and cable channels. CH 01 AUTO SET UP 6 After scanning The tuner stops on the lowest memorized channel. The TV screen returns to TV mode. CH01 · If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press the F. FWD/ button once again and the VCR will begin preset again. · If the VCR cannot find the local PBS channel at step 1, after scanning channels, "AUTO CLOCK" flashes on the TV screen. And the VCR search the local PBS channel for auto clock setting again. When the clock is not set yet, press the POWER button to turn on the VCR, then press the number buttons or CHANNEL (CH) / button to select your local PBS channel. The current time may appear on the display. If current time does not appear, follow "MANUAL CLOCK SETTING" on page 17. Note: The VCR will search through all the available channels from the lowest channel. It must scan each channel for 10 seconds to determine if that channel is transmitting the EDS (Extended Data Service) signal. If the highest channel has EDS signal, it takes many times. After a few minutes, flashing stops and current time appears on the display. NOTE: · When your local PBS channel is incorrect or is not received, the clock cannot be set automatically. In this case, follow "MANUAL CLOCK SETTING" on page 17. MANUAL CLOCK SETTING We suggest that you use a TV or radio station as your time source. In the example below, the clock is to be set to: DATE 20th March , 2000 SETTING TIME 5:40PM · Use the remote control for this procedure. · Be sure to check that the "PWR. " and the "VCR" indicators are both on. · Turn on the TV and set the TV to channel 3 or 4. Now set the CH3/CH4 switch on the back of the VCR to match the channel selected on the TV. 1 Select main menu Press the MENU button until the main menu appears. · If the clock is not set yet, CLOCK SET menu appears immediately when you press the MENU button. MENU TIMER PROGRAMMING AUTO REPEAT [OFF] PICTURE SELECT CHANNEL SET UP CLOCK SET LANGUAGE SELECT 2 Select "CLOCK SET" Press the PLAY/ or STOP/ Then press the F. FWD/ button. button to point to "CLOCK SET". MENU TIMER PROGRAMMING AUTO REPEAT [OFF] PICTURE SELECT CHANNEL SET UP CLOCK SET LANGUAGE SELECT 3 Select "MANUAL" If [ON] appears beside "MANUAL", press the F. FWD/ button. or STOP/ button to point to "MANUAL". · If it is not, press the PLAY/ Then, press the F. FWD/ · Press the REW/ button twice. [. . . ] · Set your TV to the VCR mode and/or press the VCR/TV button on the remote control so that the "VCR" indicator on the display comes on. · Fine tune your TV. On-the-air TV programs cannot be · Re-check the ANT. · Set your TV to the TV mode and/or press the VCR/TV button on the remote control so that the "VCR" indicator on the display disappears. . No operation from the infrared Remote Control · Make sure the AC cord is connected to an AC outlet. [. . . ]