User manual HITACHI VT-UX6570A

[. . . ] C3 and VCR Plus+C3 are trademarks of Gemstar Development Corporation. · 8-program/1-year preset recording. · Auto clock set feature allows you to automatically set the present time using a time signal. · Auto head cleaning system minimizes the need for accessory cleaners and professional head cleaning. [. . . ] Click to see remote control illustration. · For times with only one number (1-9) press the (0) button first, then the hour or minute. For example, if it is now 10:20AM, press (1)(0)(2)(0). "AM" and "PM" will now appear on the screen. 30 SETTING THE CLOCK -MANUALLY 6 Press the (1) button for AM or (2) for PM. For example, press the (1) button for AM. Click to see remote control illustration 7 Press the number buttons to fill in the number of the month, then the day then the year. · For dates with only one number (1-9) press the (0) button first, then the date. For example, if today is July 8 1997, press (0)(7)(0)(8)(9)(7). The correct day of the week will appear by itself. 8 Press the GUIDE button. The VCR clock is now set, and should show the correct time of day on the VCR's display. Notes: · The clock uses the 12-hour system. · An illogical time (like 13 for the hour or 20 for the month) will not be accepted. · If you press the wrong digit, exit the screen by pressing GUIDE and recall the screen to enter the correct setup. 31 PRE-TUNING THE VCR TUNER PRE-TUNING THE VCR TUNER Note: An antenna or cable must be connected to the VCR before you begin this operation. Make sure the cable box is positioned properly on the VCR. 1 Turn on the TV and select the video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the TV to AUX or VIDEO. 2 Press the GUIDE button. Click to see remote control illustration. The main on-screen menu will appear on the TV screen. 3 Press the (4) button to select the CHANNEL PRESET operation. 4 Press the (1) button to select <CATV2>. 36 CABLE BOX SETUP 5 Press the (5) button to select "CABLE BOX SETUP" menu. 6 Press the (1) button to answer "YES" to the question "IS A CABLE BOX BEING USED?" Note: Refer to the cable box owner's manual to identify the cable box output channel (usually 3 or 4). 7 Turn on your cable box and select channel 2. 8 Using the VCR remote, enter the cable box output channel numbers. Click to see remote control illustration. For example, press (0)(3) for channel 3. 9 Press the GUIDE button to enter the output channel of your cable box. · The CABLE BOX TYPE message will appear on the TV screen. 37 CABLE BOX SETUP 10 Press the two number buttons that match the code number of your cable box brand from the table below. For example, press (3)(7) for the Hitachi brand cable box. 11 Press the GUIDE button to enter your cable box brand. The VCR will change the cable box from channel 02 to channel 09 to confirm that the correct code was entered. 12 Cable box channel changed to channel 9: Press the (1) button to end this setting. Click to see remote control illustration. Your cable box and VCR are now set for VCR Plus+ program recording. [. . . ] · Press the stop button to finish recording. 78 COPYING FROM ONE VCR TO ANOTHER VCR (DUBBING) COPYING FROM ONE VCR TO ANOTHER VCR (DUBBING) Hookup If you have two VCRs, you may use one VCR to record a tape that is being played back in the other VCR. To copy from one VCR to another VCR 1 Press the AVX button on the remote control of VCR-1 so that L1 (line) appears in the display. 2 Press the REC, then PAUSE buttons on VCR-1. The VCR will go into Record/Pause. 3 Press the PLAY button on VCR-2. You will see the taped program being played on the TV. 79 COPYING FROM ONE VCR TO ANOTHER VCR (DUBBING) 4 When you see the part of the program you wish to record, press the PAUSE button on VCR-1 again to release pause and start recording. · Press the STOP button to finish recording. 80 PROBLEM GUIDE/MAINTENANCE PROBLEM GUIDE/MAINTENANCE Problem guide No power · Make sure the VCR is plugged into an AC outlet. [. . . ]